Form No. 3414-279 Rev E Flex-Force Power System™ 60V MAX Snowthrower Model No. 39901—Serial No. 319000001 and Up Model No. 39901T—Serial No. 319000001 and Up Model No. 39902—Serial No. 319000001 and Up Register at www.Toro.com.
Introduction For assistance, please see www.Toro.com/support for instructional videos or contact 1-888-384-9939 before returning this product. This machine is intended to be used by residential homeowners. It is designed for removing up to 30 cm (12 inches) of snow from patios, sidewalks, and small driveways. It is not designed for removing materials other than snow, nor is it designed for clearing off gravel surfaces.
Safety 7. Do not use a damaged or modified battery pack or battery charger, which may exhibit unpredictable behavior that results in fire, explosion, or risk of injury. 8. If the supply cord to the battery charger is damaged, contact an Authorized Service Dealer to replace it. 9. Do not use non-rechargeable batteries.
8. Do not force the machine—Allow the machine to do the job better and safer at the rate for which it was designed. 4. When servicing the rotor, be aware that the rotor can still move even though the power source is off. 9. Stay alert—Watch what you are doing and use common sense when operating the machine. Do not use the machine while ill, tired, or under the influence of alcohol or drugs. 5. 10. Operate the machine only in good visibility and appropriate weather conditions.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal137-2257 137-2257 3. Thrown object hazard—keep bystanders away. 1. Warning—read the Operator’s Manual. 2.
decal137-9456 137-9456 1. Read the Operator’s Manual. 2. Keep away from open fire or flames. decal138-6697 138-6697 3. Do not expose to rain. decal114-9034 114-9034 decal137-9455 137-9455 1. Read the Operator’s Manual. 2. Keep away from open fire or flames. 3. Do not expose to rain. decal114-9035 114-9035 1.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. No parts required – Mount the battery charger (optional). No parts required – Unfold the handle. Chute deflector 1 Install the chute deflector. Chute-control rod 1 Install the chute-control rod. Note: The battery pack is not fully charged when you purchase it. Before using the machine for the first time, refer to Charging the Battery Pack (page 12).
5. 2 Move the lower handle into place and install the lower handle knobs as shown in Figure 5. Note: You may use a wrench on the hex on the outside of the knob to tighten the knob. Unfolding the Handle Important: Tighten the knobs until the handlebar touches the side plate with no gap. No Parts Required Procedure 1. Remove the machine from the box. 2. Unfold the upper handle and allow the upper handle knobs to snap into place (A of Figure 3). 3. Tighten the handle knobs (B of Figure 3).
3 Installing the Chute Deflector Parts needed for this procedure: 1 Chute deflector Procedure g316999 Figure 6 9
Product Overview 4 Installing the Chute-Control Rod Parts needed for this procedure: 1 Chute-control rod Procedure 1. Ensure that the chute is facing forward (Figure 7). 2. With the handle facing forward, install the chute-control rod into the guide and push it down until it snaps into place (Figure 7). g318456 Figure 8 1. Discharge chute 6. Headlight 2. Chute deflector 3. Chute-deflector handle 4. Battery-compartment lid 7. ECO switch 8. Electric-start button 9. Bail 5. Chute-control rod 10.
Starting the Machine Operation 1. Ensure that the battery pack is installed in the machine; refer to Installing the Battery Pack (page 11). Installing the Battery Pack 1. Make sure that the vents on the battery are clear of any dust and debris. 2. Insert the electric-start button into the electric starter (A of Figure 10). 2. Lift up the battery-compartment lid (A of Figure 9). 3. Squeeze the bail and hold it to the handle (B and C of Figure 10). 3.
Charging the Battery Pack Important: The battery pack is not fully charged when you purchase it. Before using the machine for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. Read all safety precautions. Important: Charge the battery pack only in temperatures that are within the appropriate range; refer to Specifications (page 10).
Adjusting the Discharge Chute and Chute Deflector To adjust the discharge chute, move the handle on the chute-control rod in the direction that you wish to direct the snow stream. To adjust the chute deflector (and therefore the height of the snow stream), squeeze the trigger and raise or lower the chute deflector (Figure 15). g268087 Figure 14 1. LED indicator light 2. Charger venting areas 5. To remove the battery pack, slide the battery backward out of the charger. 6.
Clearing a Clogged Discharge Chute Operating Tips WARNING The rotor can throw stones, toys, and other foreign objects and cause serious personal injury to you or bystanders. WARNING Contacting a rotating rotor with your hands inside the discharge chute could cause serious personal injury. • Keep the area to be cleared free of all objects that the rotor blades could pick up and throw. Never use your hands to clean out the discharge chute. • Keep all children and pets away from the area of operation. 1.
Maintenance Storage Stop the machine, remove the electric-start button, remove the battery pack from the machine, and wait for all movement to stop before adjusting, servicing, cleaning, or storing the machine. Important: Store the machine, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 10). Important: If you are storing the battery pack for the off-season, charge it until 2 or 3 LED indicators turn green on the battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The machine does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the machine. 1. Remove and then reseat the battery into the machine, making sure that it is fully installed and latched. 2.
Notes:
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.