TO THE TOR OWNER. .. This Owner Manual has been especially prepared for your information and guidance in the operation and care of your new Toto Hydraulic Park master. Properly adjusted, operated and maintained, this Toto Park master will respond quickly and easily to every reasonable demand and give years of reliable service, The Toto Hydraulic Park master is manufactured by an organization of mowing machinery specialists for over 50 years.
DL ¢ MOWER LIFT ARM 0. 1 Mo Lae HYDRAULIC LIP CONTROL N0, 5 Mow Er LIFT AR setting DER 0. 7 Mows R LT 7 UNIT NG, 4 MOWER LIFT ARM NO. 1 MOWER LIFT ARM DOUBLE ACTING CYLINDER NO. 5 MOWER Hy LIFT AR HYDRAULIC LIFT CONTROLS DOUBLE ACTING CYLINDER NO.
ATTACHMENT OF MOWERS TO LIFT ARMS NO. 1 POSITION Spartan Mower POSITION Rough master Mower DOWN Connect spring in Sth ilks from yoke. Connect yoke in 4th link from end. 4 DOWN Spartan Mower DOWN Connect spring in 7th link from end.
POSITION T Spartan Mower DOWN B o up Hook spring in 3rd to 6th link from bottom. Rough master Mower Hook-spring in 3rd to 6th link from bottom.
MAIN FRAME ASSEMBLY (Front — 5 Unit) Rel. No. Ref. No. No. | Part No. Description Used No.| Part No.
. . MAIN FRAME ASSEMBLY (Front — 7 Unit) Ref. No. Ref. No. No. | Part No. Description Used No. | Part No. Description Used] 113256 Cap screw 12 27 | 30128 Link 4 2] 212-183 | Rubber Bumper 2 28 | 3-0128 Shaft 2 3 | 3.0285 Arm, Stop 2 29 | 302-5 Grease Fitting 6 4 | 3-6520 Bracket 4 30 | 8-2170 Front Cross Channel, Front 1 5| 3253 Cap screw 16 34 | 3253.21 | Lock washer 8 6 | 32146-13 | Nut 16 38 | 32177 Nut 8 7 | 3-45% Mudguard, 52262 Brace, Fender 2 * | 3-4597 Mudguard, L.H. 1 37 | 3253-4 Lock washer 12 .
DAL LV L 4241 \\40 392223 3534 MAIN FRAME ASSEMBLY (Rear Unit) Rei. No. | No. Ref. No. | No. No.| Past No. Description Used [Used No.| Part No, Description Used (Used 1 {3-0348 Bushing 3-4636 | Chain 27 2 2 180890 Arm, Short R.H.
3 3029 28 MAIN FRAME ASSEMBLY (Rear Unit) Rel. No. T No. Ref. No, | No. No..| Part No. Description Used Used No.[ Part No. Description b?d Us;d 48 [ 3-0145 | Spacer 32535 Lock washer 3-0146 Channel 5-1720 Washer 3-0144 Shalt 3-0128 Saith 3290-216 | Bevel Washer 1010 61 | 353-217 | Elbow 3256 Cap screw 8-2180 Rear Cross Channel 3219 | Sheave 8-0390 Pin, Bail Lift 30136 Chain Keeper 322-3 Cap screw 32114 | Cap screw 3253-4 | Lock washer 2] 2 Note: For attachment of mowers to Lift arms, see page 16.
DRAW BAR ASSEMBLY (5 & 7 Unit) Ref. e e, Ref. Part No. Description T No.| Part No. Description o7t 1 |324-10 | Cap screw 0| 12 38448 | Washer 0 |14 2 132536 | Lock washer 30348 | Bushing 32178 | Rut 302-5 Grease Fitting 517 4 15109 | Clamp, Draw bar 16559 | Housing (Incl. Ref.
10" & 12" CYLINDERS Rel. No. Ref. No. No. | Part No. Description Used] No. | Part No. Description Used: 1 1383-288 | Cap, End 1 9 | 353-254 | Seal, Rod 1 2 1353-253 | Seal, Piston 3 10 | 353-255 | Washer, Backup 1 3 |353-295 | Washer, Backup 2 11 | 353-289 | Cylinder Head 1 4 |32198 383256 | Rod, Wiper 1 5 |353-292 | Piston 1 13 ] 32967 Nut 4 6 | 35329 | 0" Ring 1 14 | 353290 | Piston Rod |353-286 | Barrel 353.291 | Piston Rod 1353-287 | Barrel 353-297 | Seal Kit (Incl. Ref. Nos.
/ 3B 302928 5 S _ HYDRAULIC VALVE ASSEMBLY Ref. Used | Used Ret. Used | Used No. | Part No. Description 5-UN 7-UN/ No. | Part No. Description S-UN. 7-UN 1 ] 353-315 | Screw & Washer Says, 12 120 21 | 353-347 | Shim 353-310 | Bonnet 353-307 | Lift, Check Lag 353-312 | Screw 353-308 | “'0” Ring, Cylinder 4 1353-314 | Washer 3 5 Port 353-313 | Spool Collar 353-306 | Back Up Washer Cover 353-311 | Swp Collar 6 110 25 | 353-305 | Q" Ring, Check 7 1 353-30% | Spring 3 5 Plug 353-317 | Housing & Spool Says.
INSTRUCTIONS FOR REPLACING, ADDING OR REMOVING HOUSING & SPOOL ASSEMBLY NOTE: For the purpose of these instructions, we shall consider the section containing the Main Relief Valve as the left side of the valve. 1.
mel oS mgj 32 3 . VALVE BANK (5 & 7 Unit) Ref. No. No. Ref. Part No.| Description Ussdileed| 1 No | Partner Description Used | Used 1| 5-7790 Decal, Park master 3-8293 High Pressure Hose 5-6600 Cover, Valve 3-3397 Low Pressure Hose 1 1 3 |3256-23 | Washer 3-0230 Hydraulic Hose Says. 322-29 Caseworker 5-0200 Hydraulic Hose Says.
HYDRAULIC SYSTEM m PUMP RESERVOIR FILTER o 3.3397 LOW PRESSURE HOSE SALVE RETURN HOSE FILTER TO VALVES 3-5293 HIGH PRESSURE HOSE PUMP TO SALVES MOWER NO. 3 > UNIT 54220 CYLINDER 7 5.0220 MOWER NO. 7 50200 (77"} camper s | BANK VALVE 6 VALVE 4 VALVE 1.2.3 VALVE valves MOWER NO. 2 UNIT 50200 (77" 5.0200 CYLINDER & MOWER NO. 6 CYLINDER 1.2.3 5.0200 77 5.0230 (102" — 5.0230 (102") S5 | evildoer ¢ MOWER No. 4 MOWER NO. 1§ ’1 MOWER NO.
ATTACHMENT OF MOWERS TO LIFT ARMS NOS. 2 and 3 MOWERS NOS. 4 and 5 MOWERS (Spartan & Rough master) Ref. No. Ref. No. No. Part No, Description Used No. Part No. Description Used 1 5-1706 Spring 2 1 327210 | Cotter Pin 4 2 5-5130 Lift Chain 2 2 8-0280 Shackle 4 3 3272-10 Cotter Pin 2 3 283-10 Pin 4 4 283-6 Pin 2 4 3-4636 Chain 2 5 | 52042 Shackle 2 5 | 51706 Spring 2 6 3-2198 S-Hook 2 I ’ Kis % T NOS. 6 and 7 MOWERS (Spartan) NOS. 6§ and 7 MOWERS (Rough master) Ref. No. Ref. No. No.
LUBRICATION GREASE FITTING Before servicing any of the grease fittings, clean the fitting with a rag to make sure that no foreign water will be forced into the bearing with the lubricant, The fitting should be lubricated every 50 hours with a light chassis grease (Mobil No. 2 is recommended). When servicing a fitting, make certain that the bearing is taking grease. Keep applying lubricant to the fitting until you see some of the grease coming out from the = GREASE sides of the bearing.
DRAW BAR ATTACHMENT POSITIONS WHEEL PRESSURE ~ \ PULL e @ PRESSURE 5™ ROLLER GROUND Fore transfer characteristics of the Spartan or Rough bars has three positions (see illustration ~ holes “A, master mowers result from the pull of the draw bar, B, The Park master frame clamp for attaching the draw Position REASON FOR POSITION A Less pressure on the rear rollers; greater pressure on the drive wheels— improved traction, B Dermal position when operating on level, flat terrain.
IMPORTANT ORDERING INSTRUCTIONS Repair parts are available from your TOR distributor. To insure getting correct parts without delay, furnish following information: 1. Serial number of your frame as stamped on the rear cross channel. 2. Part number, description, and quantity of each part required. 3. State whether parts should be shipped by mail or express. All repair parts are shipped F. O, B. factory. 4. Name and address where parts ars to be shipped. 5.
MAINTENANCE RECORD DATE HOURS USED LUBRICATION CHANGE HYD. FLUID FILTER SPRING SERVICE FORM 331-910 REV.