Form No. 3398-105 Rev A 18in Dethatcher Model No. 33513—Serial No. 315000001 and Up g025335 Register at www.Toro.com.
WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. 1 This spark ignition system complies with Canadian ICES-002. g025340 Figure 1 Important: This engine is not equipped with a spark arrester muffler.
Contents Safety Safety ........................................................................... 3 Safe Operating Practices........................................... 3 Slope Indicator ....................................................... 5 Safety and Instructional Decals ................................. 6 Setup ............................................................................ 8 Unfolding the Handle .............................................. 8 Checking the Engine-Oil Level.............
Operation • Always avoid sudden starting or stopping on a slope. If tires lose traction, disengage the flail blades and proceed slowly off the slope. • Never run an engine in an enclosed area. • Only operate in good light, keeping away from holes and • Follow the recommendations for wheel weights or hidden hazards. counterweights to improve stability. • Start the engine only from the operator’s position.
Slope Indicator G011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 20 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 20 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 117-4979 93-7321 1. Warning—stay away from moving parts; keep all guards in place. 1. Warning—stay away from moving parts; keep all guards in place. 125-3809 1. Warning—read the Operator’s Manual. 5. Thrown object hazard—keep bystanders away from the machine. 2.
127-4061 1. Cutting blades 4. Hold the handle to start the engine. 2. Fast 5. Release the handle to stop the engine. 3.
Setup Product Overview 2 Unfolding the Handle 1 1. Raise the handle to the operating position (Figure 4). 3 4 6 5 g025337 Figure 5 1. Operator-presence bail 4. Fuel tank 2. Handle 5. Depth-control lever 3. Throttle-control lever 6. Recoil-starter handle g025336 Figure 4 Controls 2. Slide the oval locking rings down each side of the upper handle over the lower handle, locking the handle sections together (Figure 4).
Recoil Starter Pull the recoil-starter handle to start the engine (Figure 6). Fuel Shutoff Valve Close the fuel-shutoff valve when transporting or storing the machine (Figure 6). Choke Lever Before starting a cold engine, move the choke lever forward. After the engine starts, regulate the choke to keep the engine running smoothly. As soon as possible, move the choke lever all the way rearward. Note: A warm engine requires little or no choking.
Throttle Lever Move the control forward to increase the engine speed, and rearward to decrease speed (Figure 8). 1 2 3 4 g025338 Figure 9 1. Depth-control lever 3. Hairpin cotter 2. Transport-position hole 4. Locking pin Specifications Figure 8 Note: Specifications and design are subject to change without notice. 1. Throttle lever Width 69.9 cm (27.
Operation 1 2 3 Note: Determine the left and right sides of the machine from the normal operating position. Checking the Engine-Oil Level Service Interval: Before each use or daily 1. Stop the engine, disengage the flail blades, and wait for all moving parts to stop. 5 4 2. Clean around the dipstick to prevent dirt from falling into the filler hole, which causes damage to the engine (Figure 10). Note: Ensure that the engine is level. g019686 Figure 11 1. Filler tube 2. Dipstick 4. Lower limit 5.
• Do not use gasoline containing methanol. DANGER • Do not store fuel either in the fuel tank or fuel containers In certain conditions during fueling, static electricity can be released, causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling.
Operating the Machine 5. Install the fuel-tank cap securely. 6. Wipe up any spilled gasoline. 1. Move the depth-control lever to the desired setting. 2. Start the engine. Starting and Stopping the Engine 3. Push down on the handle to raise the front wheels off the ground. 4. Slowly lower the front wheels to the ground, allowing the blades to gradually work into the grass and soil. Starting the Engine 5.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 25 hours • Change the engine oil. Before each use or daily • • • • Check the engine-oil level. Clean debris from the machine. Inspect the air-cleaner elements. Check the belt tension. If the engine is working but the flails seem underpowered, check the belt tension • Check the flail blades for wear or damage. • Check for loose fasteners. Every 50 hours • Clean the air-filter elements.
Engine Maintenance 10. Clean the foam element in warm, soapy water or in a nonflammable solvent. Servicing the Air Cleaner 11. Rinse and dry the foam element thoroughly. 12. Dip the foam element in clean engine oil, then squeeze out the excess oil. Service Interval: Before each use or daily—Inspect the air-cleaner elements. Every 50 hours—Clean the air-filter elements. Clean them more frequently in dusty operating conditions.
4. Remove the drain plug (Figure 16). 3. Move the fuel-shutoff valve to the OFF position. 4. Remove the sediment cup and O-ring (Figure 17). 1 G019428 Figure 16 1. Drain plug 2 g020282 Figure 17 5. When the oil has drained completely, lower the front wheels to the ground, replace the drain plug, and torque to 18 N-m (13 ft-lb). 1. O-ring Note: Dispose of the used oil at a certified recycling center. 2. Sediment cup 5. Wash the sediment cup in a non-flammable solvent and dry it thoroughly. 6.
Belt Maintenance Checking the Belt Tension Service Interval: Before each use or daily—Check the belt tension. If the engine is working but the flails seem underpowered, check the belt tension 1. Stop the machine on a level surface, shut off the engine, disconnect the spark-plug wire, and raise the flail blades to the highest position. Figure 18 1. Center-electrode insulator 2. Side electrode 3. Air gap (not to scale) 2.
1. Stop the machine on a level surface and shut off the engine by releasing the operator-presence bail. Maintaining the Flail Blades 2. To tighten the belt, loosen the 4 mounting nuts securing the engine to the frame. Inspecting the Flail Blades Adjusting the Belt Tension Service Interval: Before each use or daily—Check the flail blades for wear or damage. When the flail blades are worn down and are no longer functioning properly, refer to Replacing the Flail Blades (page 18).
Figure 21 1. Rod 3. Spacer 2. Flail 4. Cotter pin 8. Carefully add flails and spacers to rod in the same order as they were removed. Important: Align the rod with the formed head toward the center of the machine. 9. Add the cotter pin to lock the rod, flails, and spacers into place.
Removing the Machine from Storage Storage 1. Raise the flail blades, stop the machine, shut off the engine, and disconnect the spark-plug wire. 1. Check and tighten all fasteners. 2. Inspect the spark plug and replace it if it is dirty, worn, or cracked; refer to the engine Owner’s Manual. 2. Remove dirt and grime from the entire machine. Important: You can wash the machine with mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water, especially near the engine. 3.
Notes: 21
Notes: 22
Notes: 23
The Toro Warranty A limited warranty (see warranty periods below) SWS Turf Renovation and Tree Care Conditions and Products Covered Owner Responsibilities The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Products listed below to be free from defects in materials or workmanship. You must maintain your Toro Product by following the maintenance procedures described in the Operator’s Manual.