Operator's Manual

ManualsBrandsToro ManualsFrames5 To 7 Conversion Kit, Reelmaster Transport Frame

FormNo.3364-476RevA

5to7ConversionKit

ReelmasterTransportFrame

ModelNo.33452—SerialNo.310000001andUp

InstallationInstructions

Installation

InstallingtheHydraulic

Fittings

1.Parkthemachineonalevelsurfaceandlowerthe

cuttingunitstotheground.

2.Blockthewheelstoassuretheframeissecureto

workon.

3.Disconnectthehydraulichosecouplersfromthe

tractor.

4.RelievethepressureintheTransportFramehydraulic

system,byslowlycrackingtheconnectionsbetween

thehydrauliccouplersandthehydraulichoses

(

Figure1).Useextremecaution,whencrackingthe

connections,sooilisnotdirectedtowardtheskinor

eyes.Wraptheconnectionswitharagtohelpcatch

anyoilthatmayescape.

Figure1

1.Hydrauliccouplers2.Hydraulichoses

5.Withthecouplingsloose,cycleeachvalvesectionto

relieveanypressurebetweenthevalvesectionand

thehydrauliccylinder.

6.Carefullyremovethe4plugsfromthetopofthetwo

outboardvalvesections(

Figure2).

Figure2

1.Valvesection2.Plug

7.Onthenew90degreettings,lubricatetheO-ring

sealswithoilandinstallthettingsintothevalve

sections.Positionthettingsasshownin

Figure3.

Figure3

1.40degrees

MountingtheHydraulic

Cylinders

1.Mountacylinderresttotheundersideofthefront

crosschannelwith2bolts(1/2x1-1/2inch),tapered

washers,andlocknutsasshowninFigure5.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3364-476 Rev A 5 to 7 Conversion Kit Reelmaster Transport Frame Model No. 33452—Serial No. 310000001 and Up Installation Instructions Installation Installing the Hydraulic Fittings 1. Park the machine on a level surface and lower the cutting units to the ground. 2. Block the wheels to assure the frame is secure to work on. 3. Disconnect the hydraulic hose couplers from the tractor. 4.
PAGE 2
. Mount the butt cap end of the hydraulic cylinder to the front cross channels with a cylinder shaft, 2 tube spacers, and 2 cotter pins (3/16 x 1-3/4 inch) as shown in Figure 5. 3. Apply #2 Permatex to the threads of the new elbow fittings and install the fittings to the hydraulic cylinder. Position the fittings toward the center of the machine. 4. Connect the new short and long hydraulic hoses to the fittings on the control valve and cylinder as shown in Figure 4. Figure 4 Figure 5 1. Cylinder rest 2.
PAGE 3
Figure 6 4. Link 5. Shaft 1. Lift arm 2. Front cross channel 3. Lift bail pin 6. Mount the other end of the link to the hydraulic cylinder with 2 larger flat washers, flat washers, lock washers (3/8 inch), and bolts (3/8 x 1 inch) as shown in Figure 6. Position the larger flat washers between the link and the hydraulic cylinder end. 7. If the Transport Frame is to be used on a public road, the overall width of the frame and the mowers may not exceed 8 feet.
PAGE 4
Note: If Spartan mowers are to be attached, drawbar clamps, Part No. 5-1090 and mounting fasteners will be required to mount the drawbar to the front cross tube of the mower. Contact your local Authorized Toro Distributor for assistance. 2. If 18 inch wheels are installed on the mowers, the Toro Conversion Kit, Part No. 51–3060 will be required to allow the mowers to be raised to the transport position. Contact your local Authorized Toro Distributor for assistance. Figure 9 1. Lift arm 2.
PAGE 5
Figure 12 1. Long shackle 2. Clevis pin & cotter pin 3. Outer mounting hole 4. Spring 5. S-hook Figure 13 1. Hairpin cotters 4. Hook the spring to the fifth link in the chain from the mower and secure the other end of the spring to the lift bail with the S-hook (Figure 12). 2. Transport straps Mounting the Control Linkage and Levers 5. Repeat the procedure on the opposite side of the machine. 1.
PAGE 6
9. Check to make sure the valve spool levers (Figure 17) are in neutral (middle position) by pivoting the levers in toward the valve, or pulling them out to find the mid position. 3. Remove the 4 bolts securing the control panel cover to the control tower and remove the cover (Figure 15). Figure 15 3. Mounting bolts 1. Control panel cover 2. Control levers Figure 17 4. Remove the locknut and pivot securing the pivot block levers to the control tower (Figure 16). 5.
PAGE 7
11. Align the hole on the end of the lower control rod Figure 18 with the mounting pin in the control valve lever (Figure 17). The lever on the control tower should be in the center of the slot (neutral position) if adjusted correctly (Figure 19). Thread the lower rod into or out of the upper control tube to adjust. After each lever is adjusted, check to make sure all levers are aligned with each other. Readjust if necessary. 2.
PAGE 8
Schematics Hydraulic Schematic (Rev.
PAGE 9
Notes: 9
PAGE 10
Notes: 10
PAGE 11
Notes: 11
PAGE 12
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).