Form No. 3432-251 Rev A Universal Frame Reelmaster® Gang Mowers Model No. 33145—Serial No. 404400001 and Up Model No. 33155—Serial No. 404400001 and Up Register at www.Toro.com.
Model No. Serial No. Introduction This manual identifies potential hazards and has safety messages identified by the safety-alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. This product complies with all relevant European directives, for details please see the separate product specific Declaration of Conformity (DOC) sheet.
Contents Safety Safety ....................................................................... 3 General Safety ................................................... 3 Safety and Instructional Decals .......................... 3 Setup ........................................................................ 4 1 Setting Up the Stationary Cutting Units................................................................ 6 2 Installing the Wing Frames............................... 6 3 Installing the Trailing Kits .
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty.
Media and Additional Parts Description Use Qty. 1 Operator's Manual Read before operating. Note: Determine the left and right sides of the machine from the normal operating position. g289206 Figure 3 1. Bolt (1/2 x 1-1/4 inch) 8. Spacer 15. Stationary drawbar 22. Storage position hole 2. Small cotter pin 9. Bolt (1/2 x 2-1/2 inches) 16. Right hinge socket 23. Frame support 3. Shackle 10. Left hinge socket 17. Hinge clamp bolt 24. Hairpin 4. Clevis pin 11. Lift handle 18.
Note: If you are attaching Spartan cutting 1 units, drawbar clamps (sold separately, Part No. 5–1090) and mounting fasteners will be required to mount the drawbar to crossbar of the cutting unit (Figure 5). Contact your local authorized Toro distributor to order parts or for assistance.
6. 2 Installing the Wing Frames 3 Model 33155 for 5 Cutting Units Installing the Trailing Kits Parts needed for this procedure: 2 Left wing frame assembly 2 Right wing frame assembly 8 Locknut (1/2 inch) 8 Bolts (1/2 x 1-1/4 inches) 4 Small cotter pin 2 Left hinge socket 2 Right hinge socket 4 Grease fitting 4 Lock washer 4 Hinge clamp bolt 4 Hinge cap Position the hinge caps over hinge balls, tighten the hinge clamp bolts, and secure the hinge clamp with a small cotter pin.
g289160 Figure 9 1. Trailing hitch 4. 7 cm (2-3/4 inches) 2. Wing frame 5. Drill a 13.5 cm (17/32 inch) diameter hole here. 6. 1.9 cm (3/4 inch) 3. 3.5 cm (1-3/8 inches) g289161 Figure 8 1. Drill a 1.59 cm (5/8 inch) diameter hole here. 2. 6.35 cm (2-1/2 inches) 5. Pull the entire trailing unit forward and insert the bar under the 2 welded plates on the frame; pull the unit back, snapping the hitch into the snap hook. 6. 1.9 cm (3/4 inch) 7. Trailing bar 3. 2.2 cm (7/8 inch) 8. Trailing unit 4.
Product Overview Operation Specifications Note: Determine the left and right sides of the machine from the normal operating position. General Specifications Cutting Units 3 5 Width of Cut Approximately 2.1 m (7 ft) Approximately 3.4 m (11 ft) Overall Width — Mowers with Iron Wheels 2.4 m (94 inches) 3.8 m (148 inches) Overall Width — Mowers with Rubber Wheels 2.5 m (98 inches) Overall Length Cutting Unit Types Frame Optional Ball Coupler Kit (Part No.
During Operation • Evaluate the site conditions to determine if the slope is safe for machine operation, including surveying the site. Always use common sense and good judgment when performing this survey. During Operation Safety • Review the slope instructions, listed below, for operating the machine on slopes. Before you operate the machine, review the site conditions to determine whether you can operate the machine in the conditions on that day and at that site.
Hauling the Machine After Operation • Use care when loading or unloading the machine into a trailer or truck. After Operation Safety • Use full-width ramps for loading machine into trailer or truck. General Safety • Tie the machine down securely using straps, chains, cable, or ropes. Both front and rear straps should be directed down and outward from the machine.
Maintenance CAUTION Failure to properly maintain the machine could result in premature failure of machine systems causing possible harm to you or bystanders. Keep the machine well maintained and in good working order as indicated in these instructions. Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After each use • Lubricate the machine.
Storage Storing the Machine 1. Complete the procedure at the start of Maintenance Safety (page 12). 2. Remove grass clippings, dirt, and grime from the external parts of the entire machine. Important: You can wash the machine with mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water. 3. Check and tighten all fasteners. Repair or replace any part that is damaged or missing. 4. Paint all scratched or bare metal surfaces.
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Conditions and Products Covered Parts The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
