Form No: 3360-945 REV B ROPS HARD CAB Model No: 30391 – Serial No. 260000001 and Up ThisThis cabcab is intended to be is intended to used be on the following TORO product: used on the following products and not to be used on any other units: TORO 3280-D TORO 3320 Loose Parts List and Mounting Instructions ® This cab is manufactured for The Toro Company by Jodale Perry Corporation This product is covered by a two year limited warranty by Jodale Perry Corporation www.jodaleperry.
Table of Contents 1. Warranty 3 2. Safety Instructions 4 3. Safety Decals 6 4. Parts List 7 5. Parts Photos 8 6. Inspection Guide 11 7. Mounting Instructions 12 8. Heater Installation 16 9. Torque Specifications 19 10. Bulb Seal Schematics 20 11. Bolt Hole Alignment Schematic 21 12. Wiring Schematics 22 13.
TORO – GROUNDSMASTER 3280-D AND 3320 WARRANTY You are responsible for notifying the Commercial Products Distributor or Authorized Commercial Products Dealer from whom you purchased this product as soon as you believe a warrantable condition exists.
SAFETY INSTRUCTIONS BEFORE OPERATING • Read and understand the contents of this material before operating the vehicle. Become thoroughly familiar with the controls, capabilities and proper use of equipment. • DO NOT weld, cut, drill, or modify cab structure in any manner. • DO NOT allow children to operate vehicle. Do not allow adults to operate with out proper training. • Keep all shields and safety devices in place.
SAFETY INSTRUCTIONS While operating • • • • • • • • • • Avoid sudden stops or sharp turns. Always use safety belts. Never allow riders on top of cab while operating vehicle. Stay alert for hidden hazards and traffic. Avoid sudden starts and excessive speeds. Use extreme care when working around fences, ditches or on hillsides. Check clearances carefully before driving under any objects. Avoid operating sideways on a steep slope whenever possible.
SAFETY DECALS 1. 2. 3. Keep decals clean. Remove dirt with a wet, clean cloth when necessary. Replace safety decals if destroyed, missing, painted over, or unreadable. If the tractor safety decals are covered or obscured when the cab is mounted, purchase replacement decals form the tractor manufacturer. Mount them in a readable location at, or near, their original location before operating the tractor. New cab decals and tractor decals are available from your Toro distributor / dealer.
PARTS LIST PART DESCRIPTION Front Bracket Rear Brackets Cab Lift Brackets Front Bracket Bolts Front Bracket Nuts Front Bracket Bolts Front Bracket Nuts Isolator Fasteners Isolator Fasteners Isolator Fasteners Isolator Fasteners Isolator Fasteners Pedal Shield Fasteners Pedal Shield Fasteners Pedal Shield Fasteners Pedal Shield Fasteners Pedal Shield Fasteners Weatherseal, Shielding Weatherseal, Shielding Floormat Plug Buttons Seat Stop Bracket Pedal Shield Weldment, One Weldment, Left and Right Weldment
PARTS PHOTOS Radiator Screen Access Shield Seat Stop Rear Bracket (LH) Rear Bracket (LH) Hydraulic Pedal Box Hydraulic Pedal Box Front Mounting Bracket 8
PARTS PHOTOS Qty. 4 Qty. 8 Bolt, Hex, 1/2” x 1 1/2”, Gr.8, YD Nut, Hex, Locking, 1/2”, Gr.8, YD Qty. 2 Bolt, Hex, Locking, Nut, Flange, 7/16”, Gr.8, 7/16” x 1 1/2”, Gr.8, YD YD Qty. 4 Qty. 3 Bolt, Hex, 1/2” x 3”, Gr.8, YD Bolt, BH, 1/4” x 1, MB Nut, Flange, 1/4”, MB Qty. 3 Qty. 2 Qty. 3 Nut, Panel, 10-24 Qty. 4 Rubber, Washer 1/4” x 2 1/2” x 9/16” Qty. 2 Bolt, BH, 10-24 x 3/4” MB Snap Cap, 3/8” Qty. 4 Isolator, Rubber, 9/16” x 3”, Black Qty. 2 Qty.
PARTS PHOTOS Qty. 6 Qty. 1 Tyton Tie, #50, 0.180” x 12” Reducing Insert Tee, 1” x 1/2” Qty. 1 #6 Hose Clamp Qty. 2 3/8” NPT x 3/8” NPT x 3/8” NPT #20 Hose Clamp Qty. 1 Qty. 1 3/8” NPT x 3/8” Barb, 180° Qty. 5’ Qty. 1 Bolt Bag #6 Hose Clamp Qty. 1 O-Rubber 90° Qty. 1 30” x 24” x 11” Box Qty. 16’ O-Rubber 180° Qty.
ROPS Certified Cab, Roll Over Protection Structure Inspection Guide Cab has been certified to ISO 21299 standard ROPS certified cab like any other safety devices needs to be periodically inspected to verify that the integrity of the devise has not been compromised though normal machine use, misuse, age degrading, modifications, or rollovers.
MOUNTING INSTRUCTIONS 1. 2. 3. 4. 5. Position the machine on a level surface. Set the parking brake, lower the cutting units, turn the ignition off and remove the key. Remove roll bar from mower. Save fasteners for later reinstallation. Remove the escape window, door, and lower right window from the cab. Save fasteners for later reinstallation. Connect the fusible link harness between the battery and the positive harness on the cab wire harness.
MOUNTING INSTRUCTIONS 6. Install left hand rear bracket using fasteners saved from Step 2. 7. Install right hand rear bracket using fasteners saved from Step 2.
MOUNTING INSTRUCTIONS 8. Temporarily install front bracket using four of the 1/2” x 1 1/2” grade 8 bolts and nylon locking hex nuts. Bolt up against front platform using existing holes on front and right side of bracket and mower. 9. Use existing hole on left side of front bracket to mark area to drill hole in mower for left side fastener. 10. Remove front bracket and drill 1/2” hole on left side.
MOUNTING INSTRUCTIONS 11. Refasten front bracket loosely against front platform using only front four holes. Leave the sides unattached for now. 12. Take seat stop bracket and install in seat track at rear of travel, with the fastener in the track. 13. Install weather stripping on cab, using O-rubber provided. See Bulb Seal Schematic on the following pages. Remove left door and escape window from cab.
MOUNTING INSTRUCTIONS 16. 17. 18. 19. 20. Lower cab onto isolators. Tighten rubber isolator mount nuts to 7/8” distance between steel plates. Ensure equal distance on both sides for cab for proper fit. See Bolt Hole Alignment Schematic for order of fasteners. Fasten remaining two side bolts on front bracket through hole drilled in Step 10. Tighten all fasteners to torque specifications. Connect the cab three prong connector to the connector installed earlier. HEATER INSTALLATION 21. 22.
MOUNTING INSTRUCTIONS 23. Locate the lower radiator hose below the alternator on left side of engine. Cut out a 2“ piece of hose from the straight piece of radiator hose, and install the provided radiator hose splicer. Secure the splicer with #20 hose clamps. (101199) Install the provided 3/8” NPT x 3/8” barb straight fitting into the splicer. 24. Locate the heater hose at the base of the left cab C-Post. Route the hose into the engine bay. Ensure hose does not interfere with any moving engine parts.
MOUNTING INSTRUCTIONS 27. Take the provided drawing, and using it as a guide, drill the two 5/16” holes as shown. Take the pedal box parts and slide mechanism underneath the operator platform. 28. Bolt into place with 10-24 x 3/4” screws and 1/4” x 1” screws (both provided) 29. Take the main cab floormat and place over operator platform. Ensure that there is no pedal interference, and then glue into place.
TORQUE SPECIFICATIONS MINIMUM HARDWARE TORQUE SPECIFICATIONS FOOT-POUNDS (N-m) Size SAE Grade 8 Plated Hardware & Lock Nuts *1/4” *157 (18) *5/16” *324 (37) 3/8” 48 (65) 7/16” 77 (104) 1/2” 117 (159) 9/16” 169 (229) 5/8” 233 (316) 3/4” 413 (560) 7/8” 667 (904) Size Grade 8 Metric Hardware and Lock Nuts M10 58 (79) M12 102 (138) M16 254 (344) NOTE: Torque values shown with * are Inch-Pounds 19 Jodale • Perry
BULB SEAL SCHEMATICS 20 Jodale • Perry
BOLT HOLE ALIGNMENT SCHEMATIC 21 Jodale • Perry
WIRING SCHEMATICS 22 Jodale • Perry
WIRING SCHEMATICS 23 Jodale • Perry
WIRING SCHEMATICS 24 Jodale • Perry
TO THE PURCHASER All products are designed to give safe, dependable service if they are operated and maintained according to instructions. Read and understand this manual before installation or operation. This manual has been prepared to assist the owner and operators in the safe installation, and suitable maintenance of this cab. The information is applicable to products at the time of manufacture and does not include modifications made afterwards.
