Form No. 3414-738 Rev A 2226 Directional Drill Model No. 23803—Serial No. 400000000 and Up Software Guide Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. Read your Operator’s Manual for more information. Display Screen Buttons Home Screen Options Main Information Screen This is the first screen that appears after the initial splash screen.
Push buttons 2 and 3 to switch choose a row. g236827 Figure 5 g236823 Figure 3 1. Pipe functions 5. Engine temperature gauge 2. Fuel gauge 6. Engine load 3. Limit setting options 7. Thrust force, drill speed (rpm), or rotary torque adjustment 4. Select pipe row 8. Horn 1. Row 1 2. Row 2 3. Row 3 In manual pipe loading mode, use buttons 2 and 3 to choose a row or to load the pipe to the drill string.
Pulling Pipe in SmartTouch Mode Push button 5 to switch between thrust force, drill speed (rpm), and rotary torque. Start the SmartTouch mode with the cam assembly in the park position. Use buttons 6 and 7 to set limits for the drill speed (rpm), rotary torque, and thrust force. g236957 Figure 8 1. Go to the previous step 2. Go to the next step 1. Push button 1 to select the pull pipe option (Figure 9). 2. Push buttons 2 and 3 to select the row where you want to place the pipe (Figure 9).
3. Hold the lower right button on the left joystick (Figure 8) until the elevator lowers, the cam assembly rotates toward the operator station, and the arms fully extend (Figure 11). 4. Release the button to proceed to the next step in the sequence (Figure 12). g236959 Figure 12 g236958 Figure 10 5. Break the pipe connection; refer to Removing Drill Pipes in the Operator’s Manual. 6. Hold the lower left button on the left joystick to grip the pipe (Figure 13 and Figure 14) and release the button.
7. Hold the lower right button on the left joystick (Figure 8) until the arms fully retract (Figure 16). 10. Release the button to proceed to the next step in the sequence (Figure 19). g236960 g236962 Figure 15 Figure 19 11. Hold the lower right button on the left joystick (Figure 8) until the elevator puts the pipe back in the pipe box and the cam rotates to the home position (Figure 20). g210521 Figure 16 8. Release the button to proceed to the next step in the sequence (Figure 17).
Pushing Pipe in SmartTouch Mode Start the SmartTouch mode with the cam assembly in the park position. g210463 Figure 24 g236957 Figure 21 1. Go to the previous step 4. 2. Go to the next step 1. Push button 1 to select push pipe (Figure 22). 2. Push buttons 2 and 3 to select the row where you want to get the pipe (Figure 22). Release the button to proceed to the next step in the sequence (Figure 25). g236964 Figure 25 5.
6. Release the button to proceed to the next step in the sequence (Figure 27). g236965 Figure 27 7. Hold the lower right button on the left joystick (Figure 21) until the arms extend (Figure 28). g238411 Figure 31 11. Hold the lower right button on the left joystick (Figure 21) until the arms retract and the cam assembly returns to the home position (row 3) (Figure 33). g236967 Figure 32 g210528 Figure 28 8. Release the button to proceed to the next step in the sequence (Figure 29).
Manual Pipe Loading Manual pipe loading mode allows the operators to load and unload pipes from the cam assembly when it is rotated outside the pipe box. Note: Use 2 people to load the pipes into the cam assembly. g238408 Figure 34 1. Set the machine to manual pipe loading mode; refer to Carriage Settings Screen (page 12).. 2. Use buttons 2 and 3 to choose where you want the pipe to be placed; a row or the drill string (Figure 35).
3. Raise the elevator (Figure 36). 4. Push the cam rotate dial UP to rotate the cam assembly outside of the pipe box (Figure 36). 5. Raise the pipe loading guard (Figure 36). g238263 Figure 36 6. Use 2 people to load a pipe into the cam assembly (Figure 37). 7. Lower the pipe loading guard (Figure 37).
8. Lower the elevator (Figure 38). 9. Push the cam rotate dial DOWN to rotate the cam assembly to the location picked in step 2 (Figure 38). g238312 Figure 38 10. Loading to the drill string only: Refer to Adding Drill Pipes in the Operator’s Manual. 11. Repeat steps 3 to 9 to continue loading pipes to the pipe box. Hours Screen Options Drilling Fluid (Mud) Use Screen Machine Hours Screen To access this screen push button 2 on the Hours screen.
Maintenance Schedule Screens To access this screen, push button 3 on the Hours screen. These screens provide the user with the daily maintenance schedules and the 50-hour, 250-hour, 400-hour, and 800-hour increments. To reset the maintenance interval, refer to Maintenance PIN Screen (page 13).
Control Mode Screen Settings Screen Options Push button 2 on the Settings screen. Carriage Settings Screen Use this screen to select between the 2 joystick control options. Push the up and down buttons to switch between Mode I and Mode II. Push button 1 on the Settings screen. Use this screen to change the carriage settings. Push the OK button to switch between SmartTouch and the manual pipe loader option. Use the up and down arrows to choose the push, pull, or neutral setting.
Maintenance Options Screen Language and Units Options Screen Maintenance PIN Screen Push button 5 on the Settings screen to access the screen to switch between English and metric units. Use the up and down arrow keys to change the language and unit options. Push button 3 on the Settings screen. Push the up and down arrows to switch between Maintenance and Parameters. The Maintenance pin number is 12356.
Clock Settings Screen • The lower left icon indicates if the left joystick is Push button 7 on the Settings screen to switch between the clock options. Use the up and down arrows to adjust the parameters. • The lower right icon indicates if the right joystick is calibrated properly. calibrated properly. Calibrating the Joysticks Use this screen to check the calibration of the joysticks. Refer to Calibrating the Travel Pendant (page 18) to calibrate the travel pendant.
Engine I/O Screen To access this screen push button 2 on the I/O screen. Cam Arm I/O and Calibration Screen This screen displays engine information. To access this screen push button 3 on the I/O screen. Use this screen to calibrate the cam assembly. Push the up and down buttons to select the load position and the pipe-row position. Push button 3 to toggle the calibration on and off. g237125 Figure 54 g238451 1. Engine speed (rpm) 5. Battery voltage 2. Engine oil pressure 6.
Joystick Help Screen To access these screens push button 4 on the I/O screen. These screens show the function of each joystick button. Push the up and down arrows to scroll through the screens.
Left Joystick I/O Screen To access this screen push button 5 on the I/O screen. Push the buttons on the joysticks and ensure that the corresponding icon illuminates. g237132 Figure 62 Right Joystick I/O Screen To access this screen push button 6 on the I/O screen. Push the buttons on the joysticks and ensure that the corresponding icon illuminates.
Engine DPF I/O Screen Travel Pendant I/O and Calibration Screen To access this screen push button 8 on the I/O screen. Travel Pendant I/O Screen To access this screen push button 7 on the I/O screen. The travel pendant screen shows the voltage and position of the joystick located on the pendant. g237124 Figure 65 g237134 Figure 64 1. Manual regeneration 6. Engine stop warning 2. Regeneration interlock 7. Soot load 3. High exhaust temperature 8. Ash load 4. Inhibit regeneration 9.
Errors and Machine Information Screens Machine Information Screen To access this screen push button 3 on the Errors and Machine Information screen. This screen displays the machine information including the model, serial number, and software version. Drill Errors Screens To access this screen push button 1 on the Errors and Machine Information screen. This screen displays any drill errors. Push buttons 5 to page through the errors. Push button 6 to reset the error messages.
Machine CAN Information Screen Push button 4 to access this screen. If any of these icons are red, refer to your Service Manual.
Warning Icons Warning Carriage Crash Icon Description Resolution • The carriage is in the drill area and you try to operate the loader arm or pipe cam or To clear this warning, do the following: • You try to operate the carriage when the loader arm or pipe cam is not in the home position • Move the cam assembly to the home position and/or • Reverse the carriage Pipe Loading Guard The pipe loading guard is not in the lowered position. Lower the pipe loading guard.
Notes:
Notes:
