P PECO GRASS COLLECTION SYSTEM DESIGNED FOR: MODEL 22621223 - 24 toro z100 series OPERATOR’S MANUAL ASSEMBLY MANUAL PART#: Q0309 OPERATION $4.
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION I II PAGE SECTION Safety Safety Alert Symbols Warranty INTRODUCTION AND DESCRIPTION 1-1 Introduction 1-2 Description PREPARATION FOR USE 2-1 Modification Of Zero Turn 2-2 Attaching The Main Frame Assembly 2-3 Attaching The Lift Handle To The Aluminum Grass Container 2-4 Attaching The Aluminum Grass Container To The ZT Mower 2-5 Aluminum Grass Container Inlet Attachment 2-6 Adjustment Of The Dump Mechanism 2-7 Attachment Of The Outer Engine Mount Tube
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. WARNING! To avoid serious injury, perform maintenance on the vacuum collector; ONLY AFTER STOPPING THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP.
PECO LIMITED WARRANTY FOR NEW PRODUCTS A. WHAT IS WARRANTED? Peco extends the following warranties to the original purchaser of each new Peco consumer product subject to The following limitations. 1.
SECTION I INTRODUCTION AND DESCRIPTION 1-1 Introduction Figure 1 Rear Heat Guard Removal We are pleased to have you as a PeCo customer. Your collection system has been designed to give you a low maintenance, simple, and effective way to collect the grass clippings from your ZT mower. This manual is provided to give you the necessary instructions to properly mount and operate the collection system on your ZT mower. Please read this manual thoroughly. Understand what each control is for and how to use it.
The inlet, (Figure 7), will need to be attached to the container. Open the container, push the inlet, from the inside of the container through the hole in the container to the outside. Orient the inlet opening to face the ground. Use the tabs P#(B1668) inside of the box to hold the inlet in place. It is recommended that two people Perform this step. That way, one person on the inside of the container can position the tabs, while the other person tightens the bolts.
Figure 4 Lift Handle Assy. Figure 7 Aluminum Grass Container Assy.
Figure 8 Aluminum Grass Container Exploded View Figure 9 Misc.
2-8 Engine Mount Arm Installation 2-10 Adjustment Of The Hose Length Slide the engine mount arm assembly (Figure 10) into the outer engine mount tube. Secure the engine mount arm assembly using (1) detent pin P#(J0248). THE HOSES IN STEPS 2-11 AND 2-12 MUST BE CUT TO FIT YOUR MACHINE. FOLLOW STEPS 2-11 AND 2-12. DO NOT CUT THE HOSES UNTIL YOU HAVE TRIED TO FIT THEM ON YOUR MACHINE.
2-13 Attachment Of The Boot To The ZT Mower Deck Figure 14 Front Weight Assembly To mount the boot plate P#(B1810) to the boot P#(E1039), use (2) 3/8” x 1” carriage bolts P#(K1182) and (2) 3/8” flange nuts P#(K1215). Be sure that, when fastening the boot and boot plate together, the head of the bolt is placed from the inside of the boot. This will prevent grass from collecting on the bolts. Hang the boot onto the mower deck (Figure 13).
SECTION III OPERATING INSTRUCTIONS SECTION IV MAINTENANCE 3-1 General Safety 4-1 Maintenance Checklist Only qualified people familiar with this operator’s manual and the ZT operator’s manual should operate this machine. Before each use: 1. Check blades and spindles to be sure that no foreign objects, such as wire or steel strapping bands, are wrapped around them. 2. Inspect blades for wear. Replace if necessary.
SECTION V PARTS AND SERVICE 5-1 Parts And Service Information PeCo collection system owners should record the name and telephone number of their Service Center. Your Service Center will be happy to supply replacement parts, accessories, and do any service or repairs to your collection system. If for any reason your Service Center is unable to service your collection system or supply replacement parts, contact PeCo and include the following information on the chart below.
NOTES 14
NOTES 15
P PECO P.O. BOX 1197 ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: pecoinc1@bellsouth.net WEBSITE: WWW.LAWNVAC.
