Form No. 3442-386 Rev B e-Dingo 500 Compact Tool Carrier Model No. 22218—Serial No. 407100000 and Up Model No. 22218G—Serial No. 400000000 and Up Register at www.Toro.com.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information. This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Contents Hydraulic Fluid Specifications........................... 35 Checking the Hydraulic-Fluid Level................... 35 Replacing the Hydraulic Filter ........................... 36 Changing the Hydraulic Fluid ............................ 36 Cleaning .............................................................. 37 Removing Debris .............................................. 37 Washing the Machine ....................................... 37 Storage .................................................
Safety bucket makes the front of the machine the heavy end. Most other attachments make the front of the machine the heavy end. General Safety • Have the property or work area marked for buried lines and other objects, and do not dig in marked areas. DANGER • Read and understand the content of this Operator’s There may be buried utility lines in the work area. Digging into them may cause a shock or an explosion. Manual before starting the machine.
decal98-4387 98-4387 decal132-9051 1. Warning—wear hearing protection. 132-9051 1. Tie-down point decal133-8061 133-8061 decal108-4723 108-4723 decal137-9712 137-9712 1. Auxiliary hydraulics 3. Neutral (off) 2. Locked reverse (detent) 4. Forward decal130-2836 130-2836 1. Crushing hazard from above; cutting hazard of the hand—keep away from the attachment and the lift arm. decal130-2837 130-2837 1. Warning—do not carry passengers in the bucket. 5 1. Warning—read the Operator’s Manual. 3.
decal139-7709 139-7709 1. Water level 2. Attention—read the Operator’s Manual. decal139-7717 decal139-7707 139-7717 139-7707 1. Parking brake—disengaged 2. Parking brake—engaged decal139-7718 139-7718 1. Warning—Disconnect the power, stop the machine, read the Operator’s Manual. decal139-7708 139-7708 1. Crushing hazard from above, falling load—ensure that the quick-attach levers are locked. decal139-7721 139-7721 1.
> 23° F > -5° C decal139-8343 139-8343 139-7738 1. Recyclable Lithium-Ion 3. Electric shock hazard 2. Do not discard improperly. 4. Fire hazard decal139-7738 139-7738 1. Keep the battery at temperatures above -5° C (23° F); read the Operator’s Manual; slide the cover up and pivot it sideways to access the battery charging port, do not use a wrench. decal137-9713 137-9713 1. Warning—read the Operator's Manual. 5. Explosion hazard—avoid sparks; no fire, open flames, or smoking. 2.
Setup 1 Checking the Hydraulic Fluid Level No Parts Required Procedure Before starting the machine for the first time, check the hydraulic-fluid level; refer to Checking the Hydraulic-Fluid Level (page 35). 2 Charging the Batteries No Parts Required Procedure Charge the batteries; refer to Charging the Batteries (page 25).
Product Overview g281979 Figure 3 1. Attachment mount plate 5. Cylinder lock 9. Handle 13. Thigh support 2. Tilt cylinder 3. Auxiliary hydraulic couplers 6. Battery box 10. Lift point 14. Counterweight 7. Lift cylinder 11. Control panel 15. Operator platform 4. Loader arms 8. Wheel 12. Parking-brake lever Controls Key Switch Control Panel The key switch has 2 positions: ON and OFF (Figure 4).
Loader-Arm Lever Inch-Mode Switch • To lower the loader arms, slowly push the Press the switch to the ON position to activate Inch Mode. Use Inch Mode to slow the speed of the machine when installing or removing attachments, making small adjustments with the machine, and turning corners. loader-arm lever forward. • To raise the loader arms, slowly pull the loader-arm lever rearward. Note: Inch Mode overrides any current settings (e.g., Auxiliary-Hydraulics Lever Eco mode, attachment modes).
Parking brake is engaged. Hour meter Battery voltage Battery charge—each solid bar represents the charge in 10% increments. Eco Mode is on. Inch Mode is on. g315353 Figure 7 1. Splash screen 6. Eco or Inch Mode is on (Eco Mode shown). 2. Run screen 7. Parking brake is engaged. 3. Hours operated 8. Battery charge 4. Battery voltage 9. Instantaneous machine amperage Cold start Bucket Mode is on. 5. Attachment mode (Bucket Mode shown) Hammer Mode is on.
Service InfoCenter Menus To access the InfoCenter menu system, press the Menu Item Description menu access button while at the main screen. This will bring you to the main menu. Refer to the following tables for a synopsis of the options available from the menus: Hours Lists the total number of hours that the key, motor, and Eco Mode have been on and the traction controls have been engaged.
Specifications Operation Note: Specifications and design are subject to Before Operation change without notice. Width 89 cm (35 inches) Length 152 cm (62 inches) Height 125 cm (49 inches) Weight (without attachment) 938 kg (2,068 lb) Rated operating capacity—with 74.8 kg (165 lb) operator and the standard bucket Tipping capacity—with 74.
Performing Daily Maintenance During Operation During Operation Safety Before starting the machine each day, perform the Each Use/Daily procedures listed in Maintenance (page 27). General Safety • Do not carry a load with the arms raised. Always Adjusting the Thigh Support carry loads close to the ground. • Do not exceed the rated operating capacity, as the machine may become unstable, which may result in loss of control.
• Slow down and use extra care on hillsides. Ground • Slow down and use caution when making turns conditions can affect the stability of the machine. and crossing roads and sidewalks. Watch for traffic. • Avoid starting or stopping on a slope. If the • Stop the attachment when you are not working. • Stop the machine, shut off the machine, remove machine loses traction, proceed slowly, straight down the slope. the key, and inspect the machine if you strike an object.
Shutting Off the Machine Starting the Machine 1. Stand on the platform. 1. 2. Ensure that the parking brake is engaged and all 4 levers are in the NEUTRAL position. Park the machine on a level surface, lower the loader arms, and engage the parking brake. 2. Insert the key into the key switch and turn it to the ON position. Ensure that the auxiliary hydraulics lever is in the NEUTRAL position. 3. Turn the key switch to the OFF position and remove the key. 3.
5. Connecting the Hydraulic Hoses Raise the loader arms while tilting back the mount plate at the same time. WARNING Important: Raise the attachment enough to clear the ground and tilt the mount plate all the way back. 6. Shut off the machine and remove the key. 7. Engage the quick-attach pins, ensuring that they are fully seated in the mount plate (Figure 11). Hydraulic fluid escaping under pressure can penetrate skin and cause injury.
Removing an Attachment Accessing Protected Menus Note: The factory default PIN code for you machine is either 0000 or 1234. If you changed the PIN code and forgot the code, contact your Authorized Service Dealer for assistance. 1. Park the machine on a level surface. 2. Lower the attachment to the ground. 3. Shut off the machine and remove the key. 4. Disengage the quick-attach pins by turning them to the outside. 5.
After Operation Note: If the InfoCenter accepts the PIN code and the protected menu is unlocked, the word “PIN” displays in the upper right corner of the screen. After Operation Safety You can view and change the settings in the PROTECTED MENU. Once you access the PROTECTED MENU, scroll down to PROTECT SETTINGS option. Use the right button to change the setting. Setting the Protect Settings to OFF allows you to view and change the settings in the PROTECTED MENU without entering the PIN code.
Maintenance and Storage is responsible for training all operators and mechanics. • Store the charger indoors in a dry, secure place • Read, understand, and follow all instructions on that is out of the reach of unauthorized users. the charger and in the manual before operating the charger. Be familiar with the proper use of the charger. • Do not disassemble the charger. Take the charger to an Authorized Service Dealer when service or repair is required.
Moving a Non-Functioning Machine 3. Loosen the jam nut on each tow valve. Important: Do not tow or pull the machine without first opening the tow valves, or you will damage the hydraulic system. 1. Shut off the machine and remove the key. 2. Remove the plug covering each tow valve (Figure 15). g304100 Figure 16 1. Tow valve 4. Turn each valve counterclockwise 1 turn with a hex wrench to open them. 5. Tow the machine as required. Important: Do not exceed 4.8 km/h (3 mph) when towing. 6.
Loading the Machine Selecting a Trailer WARNING WARNING Loading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death. Loading or unloading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death (Figure 17). • Use extreme caution when operating a machine on a ramp. • Use only full-width ramps. • Load and unload the machine with the heavy end up the ramp.
Lifting the Machine Lift the machine using the lift points (Figure 19). g305397 Figure 21 g304319 Figure 19 1. Tie-down loops Maintaining the Batteries WARNING Unloading the Machine 1. Lower the ramp(s). 2. Unload the machine from the trailer with the heavy end up the ramp, carrying loads low (Figure 20). The batteries contains high voltage, which could burn or electrocute you. • Do not attempt to open the batteries. • Use extreme care when handling a battery with a cracked case.
Using the Battery Charger • When storing the machine for more than 10 days, ensure that the machine is in a cool location, out of sunlight, and at least 50% charged. Refer to Figure 22 for an overview of the battery-charger displays and cords. • If you are operating the machine in hot conditions or in sunlight, the battery may overheat. If this happens, a high-temperature alert will appear on the InfoCenter. In this condition, the machine slows down.
Connecting to a Power Source Charging the Batteries To reduce the risk of electric shock, this charger has a 3-prong grounded plug (type B). If the plug does not fit into the wall receptacle, other grounded plug types are available; contact an Authorized Service Dealer. Important: Charge the batteries only in temperatures that are within the recommended range; refer to the following table for the recommended range: Do not change the charger or the power-supply-cord plug in any way.
7. Monitoring the Charging Process and Troubleshooting Plug the charger-output connector into the charger connector on the machine. Note: The LCD status display displays messages during the course of charging. Most are routine. If there is a fault, the error indicator light will flash amber or a solid, light red. An error message will appear in the InfoCenter 1 digit at a time, starting with the letter E or F (e.g., E-0-1-1). To correct an error, refer to Troubleshooting (page 39).
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Maintenance Safety CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the switch before you perform any maintenance.
Maintenance Service Interval Maintenance Procedure • Change the hydraulic fluid. Yearly Yearly or before storage • Touch up chipped paint. Pre-Maintenance Procedures Removing and Storing the Cylinder Locks Important: Remove the cylinder locks from the rods and fully secure them in the storage position before operating the machine. Using the Cylinder Locks WARNING The loader arms may lower when in the raised position, crushing anyone under them.
Accessing Internal Components Removing the Hood Note: If you need to access the main-power connectors or fuse but cannot safely raise the loader arms to remove the hood, refer to Removing the Front Cover (page 30) for access. WARNING Opening or removing covers, hoods, and screens while the machine is running could allow you to contact moving parts, seriously injuring you. 1. Park the machine on a level surface. 2. Raise the loader arms and install the cylinder locks.
Disconnecting the Main Power Removing the Front Cover Important: Remove the front cover to access the main-power connectors and fuse only when you are unable to safely raise the loader arms to remove the hood. 1. Park the machine on a level surface, lower the loader arms, and engage the parking brake. 2. Shut off the machine, remove the key, and wait for moving parts to stop. 3. Remove the 4 bolts securing the front cover, remove the cover, and unplug the fan.
Lubrication Greasing the Machine Service Interval: Before each use or daily (Grease immediately after every washing.) Grease Type: General-purpose grease 1. Park the machine on a level surface, lower the loader arms, and engage the parking brake. 2. Shut off the machine and remove the key. 3. Clean the grease fittings with a rag. 4. Connect a grease gun to each fitting (Figure 30 and Figure 31). g004209 Figure 31 g304444 Figure 30 31 5.
Electrical System Maintenance Servicing the Batteries Electrical System Safety If you attempt to open the main compartment of a battery, you will void your warranty. If a battery requires service, contact your Authorized Service Dealer for assistance. Note: The machine is equipped with 7 lithium-ion batteries. • Disconnect the main-power connectors before repairing the machine. Charge the battery in an open, well-ventilated area, away from sparks and flames.
Servicing the Fuse 1. Park the machine on a level surface. 2. Raise the loader arms and install the cylinder locks. 3. Shut off the machine and remove the key. 4. Remove the hood; refer to Removing the Hood (page 29). 5. Disconnect the main power to the machine; refer to Disconnecting or Connecting Power to the Machine (page 32). 6. Locate the fuse and replace it (Figure 33).
Brake Maintenance Hydraulic System Maintenance Testing the Parking Brake Hydraulic System Safety Service Interval: Before each use or daily 1. Engage the parking-brake; refer to Parking-Brake Lever (page 10). 2. Start the machine. 3. Slowly attempt to drive the machine forward or rearward. • Seek immediate medical attention if fluid is injected into skin. Injected fluid must be surgically removed within a few hours by a doctor.
Hydraulic Fluid Specifications Checking the Hydraulic-Fluid Level Hydraulic Tank Capacity: 56 L (14.8 US gallons) Service Interval: Every 25 hours Use only 1 of the following fluids in the hydraulic system: Check the hydraulic-fluid level before the machine is first started and after every 25 operating hours. • Toro Premium Transmission/Hydraulic Tractor Refer to Hydraulic Fluid Specifications (page 35).
Replacing the Hydraulic Filter Changing the Hydraulic Fluid Service Interval: After the first 8 hours Service Interval: Yearly Every 400 hours 1. Park the machine on a level surface, remove any attachment, engage the parking brake, raise the loader arms, and install the cylinder locks. 2. Shut off the machine and remove the key. Important: Do not substitute an automotive oil filter; otherwise, severe hydraulic system damage may result.
Cleaning Storage Removing Debris Storage Safety Service Interval: Before each use or daily • Shut off the machine, remove the key, wait for all 1. Park the machine on a level surface, lower the loader arms, and engage the parking brake. 2. Shut off the machine and remove the key. 3. Clean any debris from the machine. moving parts to stop, and allow the machine to cool before storing it. • Do not store the machine near flames.
Battery Storage Requirements Note: You do not need to remove the batteries from the machine for storage. For temperature requirements for storage, refer to the following table: Temperature Requirements for Storage Storage Conditions Temperature Requirement Normal storage conditions -20° to 45°C (-12° to 113°F) Extreme heat—1 month or less 45° to 60°C (113° to 140°F) Extreme cold—3 months or less -30° to -20°C (-22° to -12°F) Important: Temperatures outside of this range will damage your batteries.
Troubleshooting Machine Troubleshooting Problem The machine does not drive. Possible Cause Corrective Action 1. The parking brake is engaged. 1. Disengage the parking brake. 2. The hydraulic-fluid level is low. 3. The hydraulic system is damaged. 2. Add hydraulic fluid to the reservoir. 3. Contact your Authorized Service Dealer. When at rest, the loader arms lower more than 7.6 cm (3 inches) per hour (less than 7.6 cm or 3 inches an hour is normal for the machine). 1. The valve spool is leaking. 1.
Problem Possible Cause Corrective Action Code E-0-3-7 1. Re-programming failed 1. Software upgrade failure or script operation failure. Ensure that the new software is correct. Code E-0-2-9, E-0-3-0, E-0-3-2, E-0-4-6, or E-0-6-0 1. Communication error with battery 1. Ensure that the connection of the signal wires to the battery is secure. Battery-Charger Fault Codes Problem F-0-0-1, F-0-0-2, F-0-0-3, F-0-0-4, F-0-0-5, F-0-0-6, or F-0-0-7 Possible Cause 1.
Notes:
Notes:
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.