Form No. 3446-321 Rev A Fan Kit e-Dingo 500 Compact Tool Carrier Model No. 145-1855 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Use Qty. No parts required – Prepare the machine. Fuse bracket 1 Install the fuse adapater. 3 Wire harness Relay Fan Cable tie 1 1 1 3 Route the wire harness. 4 Clip nut 4 Trim the hood. 5 Fan cover Bolt Nut Cable tie 1 4 4 1 Install the fan.
5. 1 Remove the rear cover. Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface, remove any attachment, engage the parking brake, raise the loader arms, and install the cylinder locks. 2. Shut off the engine and remove the key. 3. Remove the hood. 4. Separate the 2 main-power connectors. g354331 Figure 2 1. Bolt (3) 2. Rear cover 2 Installing the Fuse Bracket Parts needed for this procedure: 1 Fuse bracket Procedure 1.
2. Remove the existing fuse bracket. 3 Routing the Wire Harness Parts needed for this procedure: g354223 1 Wire harness 1 Relay 1 Fan 3 Cable tie Figure 4 1. Existing fuse bracket 3. Procedure Using the bolts you removed, install the new fuse bracket. g354333 Figure 7 Wire harness overview g354221 Figure 5 1. New fuse bracket 4. Install the fuse cover to the bracket. 1. Accessory connector (P03) 3. Control port (P04) 2. Relay (P02) 4.
1. Connect the wire harness (P04) to the control port connector on the machine wire harness. 2. Install the relay to the relay connector. Note: The control port connector is cable tied to the wire harness, near the controller. g354335 Figure 9 1. Relay g354332 Figure 8 1. Control port connector on machine wire harness 2. Control port connector (P04) 4 2.
3. Route the wire harness along the battery cable to the rear, right side of the machine and into the mount bracket. 4. Remove the cap from the accessory connector on the machine wire harness. Plug the accessory connector (P03) into the connector. Note: The accessory connector on the machine wire harness is cable tied to the harness near the fuse. g354334 Figure 11 1. Auxiliary connector from machine wire harness g354336 Figure 10 1. Kit wire harness 2. Battery cable 5 2.
5. Use 2 cable ties to secure the wire harness to the battery cable. 4 Trimming the Hood Parts needed for this procedure: 4 Clip nut Procedure 1. Remove the front cover from the hood. Retain the bolts. g354364 g304727 Figure 12 Figure 14 1. Bolt (4) 6. Use another cable tie to secure the relay connector to the wire harness. 2. 2. Front cover Remove and discard the clips nuts. g355216 g354366 Figure 15 Figure 13 1.
3. Cut out the template at the end of this publication. 4. Align the holes on the template with the holes in the hood. 5 Installing the Fan Parts needed for this procedure: 1 Fan cover 4 Bolt 4 Nut 1 Cable tie Procedure 1. Install the hood. 2. Install the fan cover to the fan. g354356 Figure 17 g354937 1. Kit bolt (4) Figure 16 5. 2. Fan cover Trace the inside of the template on the hood. Note: This expands the left and right sides of the hood opening 2.5 mm (0.1 inch). 6.
3. Connect the fan connector (P01) from the wire harness to the fan. 6 Installing the Covers No Parts Required Procedure 1. Install the rear cover. g354355 Figure 18 1. Fan wire harness connector 4. 2. Fan connector (P01) Use the remaining cable tie to reduce the excess slack on the wire harness. g354331 Figure 19 1. Bolt 2. 8 2. Rear cover Connect the 2 main-power connectors.
3. Secure the fan to the hood using the retained bolts from the front cover. 7 Updating the Software Parts needed for this procedure: 1 Diagnostic cable (sold separately) Procedure The following procedure must be performed by an Authorized Service Dealer. The fan will not operate without the software update. Update the machine software using the Toro DIAG software and diagnostic cable (part number 115-1944, sold separately).
g355148
