Installation Instructions

ManualsBrandsToro ManualsCompact Utility LoadersLight Kit, Dingo Compact Tool Carrier

FormNo.3443-462RevA

LightKit

Dingo

CompactToolCarrier

ModelNo.144-7101

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethefusepanel(TX525only)

Light2

Carriagebolt(5/16x1inch)

Flatwasher4

Rubbergrommet2

Nut(5/16inch)

Leftlightbracket

Rightlightbracket1

Thread-formingbolt(5/16x3/4inch)

Curvedwasher(320-Dor323traction

unitonly)

Installtherightlight.

Wireharness1

Cabletie

Routethewireharness.

Nopartsrequired

–

Completetheinstallation.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Lowertheloaderarms.

4.Shutofftheengineandremovethekey.

5.Openorremovethehood,asapplicableforyour

machine.

6.Removethenegative(-)batterycablefromthe

battery.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3443-462*

Summary of content (8 pages)

PAGE 1
Form No. 3443-462 Rev A Light Kit Dingo® Compact Tool Carrier Model No. 144-7101 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. No parts required – Prepare the machine.
PAGE 2
3 Removing the Fuse Panel Installing the Lights TX 525 Traction Units Only Parts needed for this procedure: No Parts Required Procedure 1. Pull the hairpin cotter from the bottom end of the hood prop-rod and slide the prop rod out of the retaining brackets and the prop-rod tab.
PAGE 3
2. Install a light to the outer hole of the bracket. 4. Install the other light and the switch to the bracket. g342137 Figure 6 g342140 Figure 4 1. Carriage bolt (5/16 x 1 inch) 4. Rubber grommet 2. Light 5. Nut (5/16 inch) 3. Flat washer 3. Install the left light bracket. g342138 Figure 5 1. Left light bracket 3. Thread-forming bolt (5/16 x 3/4 inch) 2. Curved washer 3 1. Switch 2. Carriage bolt (5/16 x 1 inch) 4. Flat washer 5. Rubber grommet 3. Light 6.
PAGE 4
TX 427 or TX 525 Traction Units 1. 3. Install the left light bracket. Install the right bracket. g342139 Figure 7 1. Right light bracket 2. 2. Thread-forming bolt (5/16 x 3/4 inch) g342136 Figure 9 1. Thread-forming bolt (5/16 x 3/4 inch) Install a light to the bracket. 4. 2. Left light bracket Install the other light and the switch to the bracket. g342137 Figure 10 g342140 Figure 8 1. Carriage bolt (5/16 x 1 inch) 4. Rubber grommet 1. Switch 2. Carriage bolt (5/16 x 1 inch) 4.
PAGE 5
4. 4 Route the wire harness behind the hoses and inside the right operator grip. Routing the Wire Harness Parts needed for this procedure: 1 Wire harness 2 Cable tie 320-D or 323 Traction Units g342266 g342265 Figure 11 Figure 13 1. Left light 4. Machine main harness 2. Switch 5. Right light 1. Right light 3. Fuse (10 A) 1. Connect the wire harness to the left light and switch. 5. Connect the right light. 6. Secure the wire harness to the left light bracket.
PAGE 6
7. Secure the wire harness to the bottom flow divider hose (320-D traction units only) or to the front, left side of the control panel. 2. Cut a slot in both control panel covers as shown. WARNING Using a drill without proper eye protection may allow debris to enter the eye, causing injury. When drilling or carrying out other operation, always wear eye protection. g342450 Figure 15 1. Flow divider (320-D traction units only) 2. Cable tie TX 427 or TX 525 Traction Units g342398 Figure 16 1.
PAGE 7
5. Route the wire harness across the front of the machine and connect the wire harness to the machine wire harness (P09). g342396 Figure 21 1. Kit machine harness connector 2. Light kit connector from machine wire harness (P09) g342400 Figure 19 Right control panel cover 3. Connect the wire harness to the left light and switch. 6. 3. Fuse Route the wire harness back to the control panel and connect it to the right light. g342397 Figure 22 g342402 Figure 20 1. Right light. 1. Left light 4. 2.
PAGE 8
. Secure the wire harness to the left light bracket. 5 Completing the Installation No Parts Required Procedure 1. For the TX 525, install the fuse panel. Note: Reverse the procedure for 2 Removing the Fuse Panel (page 2). g342385 Figure 23 1. Cable tie 9. Install the negative (-) battery cable to the battery. 3. Close or install the hood, as applicable for your machine. 4. Start the machine and verify that the lights function using the switch. 2.