Form No. 3443-451 Rev A Light Kit Dingo® TX 1000 Compact Tool Carrier Model No. 144-7100 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
1 2 Preparing the Machine Installing the Front Light No Parts Required Parts needed for this procedure: Procedure 1 Light 1 Front light bracket 1. Park the machine on a level surface. 1 Carriage bolt (5/16 x 1 inch) 2. Engage the parking brake. 4 Bolt (1/4 x 5/8 inch) 3. Lower the loader arms. 1 Lock washer 4. Shut off the engine and remove the key. 4 Washer 5. Open the rear-access cover. 1 Nut (5/16 inch) 6. Turn the battery-disconnect switch to the OFF position.
2. Install the front light bracket in the center of the hood. 3 Installing the Rear Light Parts needed for this procedure: g341814 Light 1 Rear light bracket 1 Bolt (5/16 x 3/4 inch) 1 Carriage bolt (5/16 x 1 inch) 1 Lock washer 1 Nut (5/16 inch) Procedure Figure 3 1. Bolt—1/4 x 5/8 inch (4) 1 1. 3. Nut—1/4 inch (4) 2. Washer (4) Remove and discard the bolt securing the top of the right cushion. g341694 Figure 4 1.
2. Install the rear light bracket. 4 Installing the Switch Parts needed for this procedure: Figure 5 3. Switch 1 Switch bracket 2 Bolt (1/4 x 3/4 inch) 2 Locknut (1/4 inch) Procedure g341692 1. Rear light bracket 1 1. Install the switch bracket to the left frame plate. 2. Bolt (5/16 x 3/4 inch) Install a light to the bracket. g341816 Figure 7 1. Bolt—1/4 x 3/4 inch (2) 2. Switch bracket g341693 Figure 6 1. Carriage bolt (5/16 x 1 inch) 3. Lock washer 2. Light 4.
2. Install the switch to the bracket. g341817 Figure 8 1. Switch 5 Routing the Wire Harness Parts needed for this procedure: 1 Wire harness 2 Cable tie Procedure g341986 Figure 9 1. Front light 3. Machine harness connector 2. Switch 4. Accessory connector 5 5.
1. Connect the wire harness to the front light. g341983 Figure 10 1. Front light 2. Switch 2. Route the cable over the hood and connect the switch connector to the switch. 3. Route the cable over the left frame plate, and follow the hydraulic hoses through the hole. 4. Follow the machine wire harness through the rear of the machine. g341985 Figure 11 1. Accessory and machine harness connectors 5. 2.
6. Inside the hood, connect the machine harness connector to the light kit connector (P15) on the machine wire harness. Note: Use the accessory connector from the kit wire harness to connect any other powered accessories. g341984 Figure 12 1. Kit machine harness connector 3. Accessory connector 2. Light kit connector from machine wire harness 7. Close the hood. 8. Use 2 cables to secure the wire harness away from moving parts. g341992 Figure 13 1. Secure the wire harness to the hood. 2.
6 7 Installing the Reflectors Completing the Installation Parts needed for this procedure: No Parts Required 2 Long reflector 2 Short reflector Procedure Procedure 1. Install the front reflectors. 1. Turn the battery-disconnect switch to the ON position. 2. Close the rear-access cover. 3. Install the cover plate. g341818 Figure 14 2. g038212 Install the rear reflectors. Figure 16 1. Bolt—1/4 x 3/4 inch (3) g341819 Figure 15 8 2. Cover plate 4. Close the hood. 5.
