Installation Instructions

ManualsBrandsToro ManualsMisc.Roller Rebuild Tool Kit, Greensmaster Cutting Units

FormNo.3441-170RevA

RollerRebuildToolKit

Greensmaster

CuttingUnits

ModelNo.140-5553

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Bearing/outer-sealtool

Assemblywasher1

Rebuildtheroller.

TheRollerRebuildT oolKitisusedinconjunctionwith

theRollerRebuildKit(Part140-5552),whichincludes

newbearings,bearingnuts,outerseals,andV-rings

forrebuildingagreensroller.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Lowerthecuttingunits(ifapplicable).

4.Shutoffthemachineandremovethekey(if

applicable).

RebuildingtheRoller

Partsneededforthisprocedure:

Bearing/outer-sealtool

1Assemblywasher

DisassemblingtheRoller

1.Removetherollerfromthecuttingunit.

2.Removethebearinglocknuts,seals,rollershaft,

andbearingsfromtherollertube(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3441-170*

Summary of content (4 pages)

PAGE 1
Form No. 3441-170 Rev A Roller Rebuild Tool Kit Greensmaster® Cutting Units Model No. 140-5553 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description No parts required – Prepare the machine. Bearing/outer-seal tool Assembly washer 1 1 Rebuild the roller.
PAGE 2
g332527 Figure 3 Cross-section view g331649 1. Bearing Figure 1 1. Roller tube 2. Roller shaft 4. Outer seal 5. V-ring 3. Bearing 6. Bearing locknut 3. 3. Bearing/outer-seal tool 2. Assembly washer 3. Clean the roller shaft and all of the surfaces on the inside of the roller-tube assembly. Inspect the shaft and tube assembly for wear. Replace as necessary. 4. 5. Installing the Bearings Use your finger to check the rotation of the bearing.
PAGE 3
Important: To prevent damage to the washer and bearing/outer-seal tool on the other side to prevent the first bearing from moving outwards (Figure 7). bearing, carefully tap on the assembly washer, which contacts the inner and outer bearing race with the washer when installing the bearing. Installing the Outer Seals 1. Fill each outer-seal cavity 75% to 90% full with number 2 general-purpose grease (Figure 8). g332517 Figure 5 1. Bearing 3. Bearing/outer-seal tool 2.
PAGE 4
g332528 Figure 10 Cross-section view g332542 Figure 12 Cross-section view 1. Bearing 3. Assembly washer 2. Outer seal 4. Bearing/outer-seal tool Installing the V-rings and Bearing Locknuts 1. 1. Bearing 3. V-ring 2. Outer seal 4. Bearing locknut 4. Wipe off any visible grease from the roller. 5. Using a 25 mm (1 inch) wrench on the bearing nut, rotate the roller several times to lubricate all the seals inside roller and remove excess drag in the seals. 6.