Installation Instructions

ManualsBrandsToro ManualsCompact Utility LoadersSelf Leveling Kit, TXL 2000 Tool Carrier

FormNo.3436-312RevA

SelfLevelingKit

TXL2000ToolCarrier

ModelNo.139-7133

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Mountbracket1

Carriagebolt(3/8x1inch)

Nut(3/8inch)

Self-levelingvalve

Straighttting

Elbowtting

Bolt(5/16x2-1/2inches)

Nut(5/16inch)

Installthebracketandvalve.

Straighttting

Tubewithcentertting

Tubewithextraendtting

Tube1

Bulkheadtube1

Elbowtting

Installthehydraulictubes.

Switch

Wireharness1

Installtheswitch.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Lowertheloaderarms.

3.Shutofftheengineandremovethekey.

4.Opentherear-accesscover.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3436-312*A

Summary of content (8 pages)

PAGE 1
Form No. 3436-312 Rev A Self Leveling Kit TXL 2000 Tool Carrier Model No. 139-7133 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty.
PAGE 2
. 2 Install 2 straight fittings and 2 elbow fittings to the self-leveling valve (Figure 2). Installing the Bracket and Self-Leveling Valve Parts needed for this procedure: 1 Mount bracket 3 Carriage bolt (3/8 x 1 inch) 3 Nut (3/8 inch) 1 Self-leveling valve 2 Straight fitting 1. Straight fitting (2) 2 Elbow fitting 2. Self-leveling valve 2 Bolt (5/16 x 2-1/2 inches) 2 Nut (5/16 inch) g311823 Figure 2 Procedure 1.
PAGE 3
5. 3 Disconnect the hose from port B2 (top, middle) on the lift valve (Figure 5). Installing the Hydraulic Tubes Parts needed for this procedure: 1 Straight fitting 1 Tube with center fitting 1 Tube with extra end fitting 1 Tube 1 Bulkhead tube 1 Elbow fitting g312132 Figure 5 Procedure 1. 1. Tube with extra end fitting 3. Port B2 (top, middle) 2. Hose from port B2 (top, middle) 4. Elbow fitting 6.
PAGE 4
10. Remove and discard the tube connected to port A1 (bottom, right) on the lift valve and the mount plate (Figure 6). Retain the bulkhead nut. 11. Install the tube to port B (right) on the self-leveling valve and port A1 (bottom, right) on the lift valve (Figure 7). 16. g312179 Figure 7 1. Port B (right) 3. Port A1 (bottom, right) 2. Tube 12. Install the bulkhead tube to port A (rear) on the self-leveling valve and the mount plate (Figure 8).
PAGE 5
4. 4 Route the wire harness, following the machine wire harness, through the hole on the left side toward the front of the machine (Figure 10). Installing the Switch Parts needed for this procedure: 1 Switch 1 Wire harness Procedure 1. Open the hood. 2. Plug the wire harness in the back of the self-leveling valve. 3. Plug the accessory power-in connector (P03) to an accessory connector on the machine wire harness (Figure 9). 1. Wire harness Note: Use the accessory power-out connector 5.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8