Form No. 3426-279 Rev B Hot Oil Shuttle Kit 2226 Directional Drill Model No. 139-2475 Installation Instructions Parts List 1x 1x 1x 1x 1x 1x 2x 4x 2x 2x 1x 3x 43 cm (17-1/2 inch) — 1x 45 cm (18-1/2 inch) — 1x 84 cm (33 inch) — 1x © 2019—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Register at www.Toro.com.
Installing the Manifold 1. Move the machine to a level surface, shut off the engine, remove the key, turn the battery disconnect switch to the OFF position, and wait for the engine to cool; refer to the Operator’s Manual. g269652 Figure 1 2. Install and hand tighten the fittings onto the manifold (Figure 2). g269651 Figure 2 3. Install the plug onto the manifold (Figure 2) and torque to 46 to 57 N∙m (34 to 42 ft-lbs).
4. Remove and discard the bolts on the charge filter mount (Box A of Figure 3). g269650 Figure 3 5. Install the bracket using 4 bolts (3/8 inch) as shown in Box B of Figure 3. 6. Install the manifold and fittings onto the bracket using 2 bolts (1/4 x 2-3/4 inches) and 2 nuts (1/4 inch) as shown in Box C of Figure 3).
Installing the Hoses Installing the 84 cm (33 inch) Hose 1. Cut the cable ties on the hose guard and set the guard aside (Box A of Figure 4). 2. Disconnect the hose from the fitting on the case drain hard line (Box B of Figure 4). g269658 Figure 4 3. Install the large tee between the fitting and disconnected hose (Box B of Figure 4). 4. Install the 84 cm (33 inch hose) in port CD on the manifold and the top of the tee fitting (Box C and D of Figure 4).
. Torque the fittings (Figure 5): Important: Support the tee fitting with a crows foot on a long extension or from the side with a board or hammer handle. • Fitting on the manifold: 78 to 98 N∙m (58 to 72 ft-lb) • 84 cm (33 inch) hose in port CD: 50 to 64 N∙m (37 to 47 ft-lb) • 84 cm (33 inch) hose connecting to the tee fitting: 81 to 100 N∙m (60 to 74 ft-lb) • Tee fitting: 81 to 100 N∙m (60 to 74 ft-lb) • Existing hose connecting to the tee fitting: 81 to 100 N∙m (60 to 74 ft-lb) g270999 Figure 5 1.
Installing the 43 cm (17-1/2 inch) Hose 1. Disconnect the hose from the upper hard line going to the rotary hydrostat (Box A of Figure 7). 2. Install a small tee between the hard line fitting and the disconnected hose (Box B of Figure 7). 3. Connect the 43 cm (17-1/2 inch) hose to the P2 fitting to the tee fitting (Box C of Figure 7).
4. Torque the fittings (Figure 8): • Fitting on the manifold: 78 to 98 N∙m (58 to 72 ft-lb) • 43 cm (17-1/2 inch) hose in port P2: 37 to 45 N∙m (27 to 33 ft-lb) • 43 cm (17-1/2 inch) hose connecting to the tee fitting: 37 to 45 N∙m (27 to 33 ft-lb) • Tee fitting: 37 to 45 N∙m (27 to 33 ft-lb) • Existing hose connecting to the tee fitting: 37 to 45 N∙m (27 to 33 ft-lb) g271000 Figure 8 1. Fitting on the manifold 4. Tee fitting 2. 43 cm (17-1/2 inch) hose in port P2 5.
Installing the 45 cm (18-1/2 inch) Hose 1. Disconnect the hose from the lower hard line going to the rotary hydrostat (Box A of Figure 9). 2. Install a small tee between the hard line fitting and the disconnected hose (Box B of Figure 9). 3. Connect the 45 cm (18-1/2 inch) hose to the P1 fitting to the tee fitting (Box C of Figure 9).
4. Torque the fittings (Figure 10): • Fitting on the manifold: 20 to 26 N∙m (15 to 19 ft-lb) • 45 cm (18-1/2 inch) hose in port P1: 37 to 45 N∙m (27 to 33 ft-lb) • 45 cm (18-1/2 inch) hose connecting to the tee fitting: 37 to 45 N∙m (27 to 33 ft-lb) • Tee fitting: 37 to 45 N∙m (27 to 33 ft-lb) • Existing hose connecting to the tee fitting: 37 to 45 N∙m (27 to 33 ft-lb) g270998 Figure 10 1. Fitting on the manifold 4. Tee fitting 2. 45 cm (18-1/2 inch) hose in port P1 5.
Notes:
Notes:
