Installation Instructions

ManualsBrandsToro ManualsCompact Utility LoadersPump Bracket Kit, TX 1000 Compact Tool Carrier

FormNo.3434-498RevA

PumpBracketKit

TX1000CompactToolCarrier

ModelNo.138-7172

InstallationInstructions

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Removeanyattachments.

3.Raisetheloaderarmsandsecurewiththe

cylinderlocks.

4.Engagetheparkingbrake,shutofftheengine

andremovethekey.

5.Toggletheloaderarmleverbackandforthto

relievethepressureintheliftcylinders.

RemovingtheCovers

NoPartsRequired

Procedure

1.Removethefrontcover(Figure1).

g256988

Figure1

1.Upperbolt—3/8x1inch

(2)

3.Washer(2)

2.Frontcover

4.Lowerbolt—5/16x5/8

inch(2)

2.Removethetopcover(Figure2).

g291502

Figure2

1.Bolt—3/8x1inch(2)

2.Topcover

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3434-498*A

Summary of content (8 pages)

PAGE 1
Form No. 3434-498 Rev A Pump Bracket Kit TX 1000 Compact Tool Carrier Model No. 138-7172 Installation Instructions Installation 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Remove any attachments. 3. Raise the loader arms and secure with the cylinder locks. 4. Engage the parking brake, shut off the engine and remove the key. 5. Toggle the loader arm lever back and forth to relieve the pressure in the lift cylinders. g256988 Figure 1 1.
PAGE 2
3. 3 Remove the 2 bolts securing the bracket to the pump (Figure 4). Removing the Pump Bracket No Parts Required Procedure 1. Mark the location of the hoses connected to the 2 tee fittings (Figure 3). g290333 Figure 4 1. Bolt (2) 4. Remove the pump mount bracket (Figure 5). Retain the washer and spacer. g290277 Figure 3 1. Tee fittings 2. 2. Pump mount bracket Disconnect the hoses from both tee fittings and move them to the side (Figure 3). g290334 Figure 5 1. Bolt 2. Washer 3. Spacer 2 4.
PAGE 3
5. Remove and retain the isolator mount and fasteners (Figure 6). 4 Installing the New Bracket Parts needed for this procedure: 1 Pump mount bracket 1 Bulkhead bracket 2 Socket-head bolt 1 Bolt (3/8 x 2-3/4 inch) 1 Nut (3/8 inch) 1 Thread-locking compound Procedure 1. g290336 Figure 6 1. Bolt—5/16 x 7/8 inch (2) Install the isolator mount to the pump mount bracket using the fasteners removed previously (Figure 7). 3. Nut—5/16 inch (2) 2. Isolator mount g290588 Figure 7 3 1.
PAGE 4
2. Install the pump mount bracket and bulkhead bracket to the cross bracket on the machine (Figure 8). g290589 Figure 9 1. Socket-head bolt—M10 (2) 4. g290586 Figure 8 1. Bolt (3/8 x 2-3/4 inches) 5. Nut (3/8 inch) 2. Existing washer 6. Pump mount bracket 3. Existing spacer 7. Bulkhead bracket Install the tee-fittings that were removed previously (Figure 10). Torque the first bulkhead nut on each fitting to 43 to 52 N∙m (32 to 38 ft-lb), and loosely install the second nut. 4. Cross bracket 3.
PAGE 5
2. Install the front cover (Figure 13). g290444 Figure 11 6. Tighten the second bulkhead nut on both fittings and torque to 37 to 45 N∙m (27 to 33 ft-lb). g256988 Figure 13 5 Installing the Covers No Parts Required Procedure 1. Install the top cover (Figure 12) g247902 Figure 12 1. Bolt—3/8 x 1 inch (2) 5 1. Upper bolt—3/8 x 1 inch (2) 3. Washer (2) 2. Front cover 4. Lower bolt—5/16 x 5/8 inch (2) 3. Remove the cylinder locks and store them. 4.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8