Use and Care Manual

ManualsBrandsToro ManualsMulching & Striping42 in. Recycler Kit for TimeCutter SS and SW 2018 and After Models

FormNo.3418-272RevA

42inRecycler

Kit

RidingMower

ModelNo.137-7042

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Preparethemowerdeck.

Dischargecover1

Bafe

Knob1

Installthebafeanddischargecover.

Decal1Installthedecal.

Mulchingblade2Installtheblades.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3418-272*A

Summary of content (8 pages)

PAGE 1
Form No. 3418-272 Rev A 42in Recycler® Kit Riding Mower Model No. 137-7042 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 © 2017—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Use Qty.
PAGE 2
1 3 Preparing the Machine Installing the Baffle and Discharge Cover No Parts Required Parts needed for this procedure: Procedure 1. Park the machine on a level surface. 2. Disengage the PTO, engage the parking brake, and move the motion-control levers outward to the NEUTRAL-LOCK position. 3. Shut off the engine and remove the key. 4. Disconnect the spark-plug wires from the spark plugs. 1 Discharge cover 1 Baffle 1 Knob Procedure 1. Install the baffle and knob (Figure 1).
PAGE 3
g230248 Figure 2 1. Discharge cover 3. Bracket on the mower deck 2. Metal tab 3. Pivot the discharge cover back and toward the deck so that the discharge cover aligns with the mower deck (Figure 3). g230253 Figure 4 1. Deflector 2. Latch 5. Secure the discharge cover to the deck by hooking the flexible latch on the discharge cover into the retainer on the deck (Figure 6). 4 g230249 Figure 3 4. 3. Pivot rod 4.
PAGE 4
5 Installing the Blades 4. Release the hook-shaped latch on top of the discharge cover from the pivot rod (Figure 4). 5. Angle the metal tab on the discharge cover out of the slot in the bracket welded to the mower deck (Figure 7). Parts needed for this procedure: 2 Mulching blade Procedure 1. Install the mulching blades; refer to the Operator’s Manual for the machine. Note: Do not install a blade stiffener. These 2. 3. blades do not require the blade stiffener.
PAGE 5
Operating Tips Selecting the Proper Height-of-Cut Setting to Suit the Conditions Remove approximately 1 inch or no more than 1/3 of the grass blade when cutting. In exceptionally lush and dense grass you may need to raise the height-of-cut setting another notch or convert to side discharge or bagging operations. Mowing in Extreme Conditions Air is required to cut and recut grass clippings in the mower housing, so do not set the height-of-cut too low or totally surround the housing by uncut grass.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8