Installation Instructions

ManualsBrandsToro ManualsGreens RollerRoller Support Kit, GreensPro 1240 Series Greens Roller

FormNo.3407-676RevA

RollerSupportKit

GreensPro

™

1240SeriesGreensRoller

ModelNo.136-6160

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Rollersupport2

Rubberpad8

Screw(5x25mm)

Locknut(5mm)

Washer(5mm)

Installtherubberpads.

Spring

Flange-headbolt(8x40mm)

Flange-headbolt(8x45mm)

Installthekit.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonlevelground,engagethe

parkingbrake,andshutofftheenginebeforemaking

adjustmentstothemachine.

2.Raisethemachine,usingasuitablehoistorlift.

Important:Ensurethatthemachineisproperly

supportedtopreventmovementduringthe

installationofthekit.

3.Removetherollercylindersfromthesteeringheads

(Figure1).

Note:Retainallofthehardwareforlaterinstallation.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3407-676*A

Summary of content (4 pages)

PAGE 1
Form No. 3407-676 Rev A Roller Support Kit GreensPro™ 1240 Series Greens Roller Model No. 136-6160 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Use Qty.
PAGE 2
Figure 1 1. Bolt (spring) 5. Roller cylinder 2. Nut 6. Washer (roller) 3. Washer (spring) 7. Split washer 4. Locknut 8. Bolt (roller) Figure 3 4. Remove the bolts, the nuts, and the washers securing the springs to each steering head and the frame. 1. Locknut (8) 4. Steering bearing assembly 2. Washer (existing), 16 5. Grommet (2) 3. Roller support (2) Note: Retain the nuts and washers for later installation. 5. Remove the steering heads from the machine as shown in Figure 2.
PAGE 3
Figure 4 1. Roller support (2) 4. Rubber pad (8) 2. Locknut—5 mm (8) 5. Screw—5 x 25 mm (8) 3. Washer—5 mm (16) Figure 5 3 1. Locknut (8) 4. Steering bearing assembly 2. Washer (existing), 16 5. Bolt—M10 x 40 mm (8) 3. Roller support (2) 2. Install a grommet into the top side of the hole in each roller support as shown in Figure 6. Installing the Kit Parts needed for this procedure: 2 Spring 2 Flange-head bolt (8 x 40 mm) 2 Flange-head bolt (8 x 45 mm) Procedure 1.
PAGE 4
1 2 2 1 G025386 Figure 9 1. Joints 5. Connect each of the 2 springs to the appropriate steering head, using the flange-head bolts provided and the washers, nuts, and locknuts previously removed; refer to Figure 10. Figure 7 Steering head not shown for clarity 1. Carriage screw (4) 3. Locknut—M10 (8) 2. Washer—M10 (16) 4. Bolt (4) 2. Short roller tube Note: Keep part of the shank on each bolt exposed so that the springs can move freely.