Installation Instructions

ManualsBrandsToro ManualsGreens RollerDrawbar Service Kit, GreensPro 1240 Greens Roller

FormNo.3432-200RevA

DrawbarServiceKit

GreensPro

™

1240GreensRoller

ModelNo.134-1693

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethedrawbar.

Nopartsrequired

–

Disassemblethedrawbar.

Slide

Drawbar1

Hitchlever1

Bolt(8x65mm)

Bolt(8x75mm)

Assemblethedrawbar.

Nopartsrequired

–

Installthedrawbar.

Nopartsrequired

–

Completetheinstallation.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface,engagethe

parkingbrake,shutofftheengine,andwaitfor

allmovementtostop.

2.Disconnectthespark-plugwirefromthespark

plug;refertotheOperator’sManualforyour

machine.

3.Partiallyraisethetransportwheelsasshownin

Figure1;refertotheOperator’sManualforyour

machine.

g287751

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3432-200*A

Summary of content (8 pages)

PAGE 1
Form No. 3432-200 Rev A Drawbar Service Kit GreensPro™ 1240 Greens Roller Model No. 134-1693 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. No parts required – Prepare the machine. No parts required – Remove the drawbar. No parts required – Disassemble the drawbar. Slide Drawbar Hitch lever Bolt (8 x 65 mm) Bolt (8 x 75 mm) 1 1 1 1 1 Assemble the drawbar.
PAGE 2
3 Removing the Drawbar Disassembling the Drawbar No Parts Required No Parts Required Procedure Removing the Roll Pin from the Drawbar 1. Note which holes in the hitch bracket the 10 mm bolt securing the drawbar is installed (Figure 2), . and record the location here: 1. Rotate the hitch lever down to retract the slide, and secure the lever to the drawbar (Figure 4). g287905 Figure 2 g287769 Figure 4 2.
PAGE 3
Removing the Tow Pin from the Drawbar Remove the locknut and washer that retain the tow pin to the drawbar, and remove the pin (Figure 6). g287770 Figure 7 g287768 Figure 6 1. Locknut 1. 2. 3. 4. 3. Tow pin 2. Washer Removing the Link and Lever 1. Remove the bolt, 2 washers, and locknut that retains the hitch lever to the drawbar (Figure 7). 5. Clevis fork 6. Jam nut 7. Lever rod 2. Rotate the lever and link as shown in Figure 7. 3. Loosen the jam nut (Figure 7). 4.
PAGE 4
Disassembling the Link and Hitch Lever Remove the cotter pin and clevis pin that secure the link to the hitch lever, and remove the lever (Figure 7). Discard the hitch lever. g287765 Figure 9 1. Locknut 2. Lever rod 3. Spring g287778 Figure 8 1. Clevis pin 4. Link 2. Hitch lever 3. Cotter pin 5. Washer 6. Hitch lever 2. 1. Remove the bolt, 2 washers, and locknut that secures the lever rod to the drawbar, and remove the lever rod (Figure 9). Discard the bolt.
PAGE 5
Removing the Rubber Blocks 1. 4 Remove the button-head screw that secures the rubber block to the slide, and remove the block (Figure 10). Assembling the Drawbar Parts needed for this procedure: 1 Slide 1 Drawbar 1 Hitch lever 1 Bolt (8 x 65 mm) 1 Bolt (8 x 75 mm) Assembling the Rubber Blocks 1. Assemble the rubber block and button-head screw (5 x 12 mm) the that you removed in Removing the Rubber Blocks (page 5) to the new slide (Figure 11). g287767 Figure 10 1. Button-head screw 2.
PAGE 6
Assembling the Link to the Hitch Lever 1. Assemble the link that you disassembled in Disassembling the Link and Hitch Lever (page 4) to the new hitch lever with the clevis pin as shown in Figure 12. g287831 Figure 13 g287828 Figure 12 1. Lever rod 4. Bolt (8 x 65 mm) 1. Hitch lever 3. Clevis pin 2. Locknut (8 mm) 5. Locknut (6 mm) 2. Cotter pin 4. Link 3. Washer (8 mm) 6. Slide 2.
PAGE 7
Assembling the Hitch Lever to the Drawbar 1. Assembling the Hitch Pin to the Drawbar Thread the jam nut onto the lever rod (Figure 14). 1. Rotate the hitch lever up to retract the slide, and secure the lever (Figure 15). g287896 Figure 15 g287895 Figure 14 1. Clevis fork 2. Jam nut 3. Lever rod 5. Washers 6. Hitch lever 7. Bracket (drawbar) 4. Bolt (8 x 75 mm) 8. Locknut 1. Hitch pin 3. Washer (16 mm) 2. Locknut (16 mm) 4. Upper tab (drawbar) 2.
PAGE 8
Assembling the Roll Pin to the Drawbar Install the roll pin that you removed in Removing the Roll Pin from the Drawbar (page 2) into the hole (8 mm) in the lower tab of the drawbar (Figure 16). Note: Ensure that the roll pin is flush with the top of the tab. g287898 Figure 17 g287897 1. Washer (10 mm) 5. Locknut (12 mm) 2. Hitch bracket 6. Washer (12 mm) 3. Capscrew (10 x 100 mm) 7. Drawbar 4. Locknut (10 mm) 8. Capscrew (12 x 100 mm) 2.