Parts Catalogue

ManualsBrandsToro ManualsUtility VehicleToro 132-3128

 NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain

these Installation Instructions for future reference.

Arctic Cat

Prowler

Installation Instructions - Accessory Kit

Form No. 0453-635

Cab Heater Kit

(p/n 1436-877)

Application: All Prowler models

Kit includes:

p/n QTY DESCRIPTION

0541-852 1 Heater

1441-934 2 Side Mounting Bracket

1441-935 1 Rear Mounting Bracket (Left-Side)

1441-978 1 Rear Mounting Bracket (Right-Side)

1441-936 1 Vent Hose (2 in. x 10 ft)

1441-937 4 Round Adjustable Vent

0541-896 1 Vent Hose “Y” Fitting

1441-939 1 Heater Hose (20 x 3/4-in.)

1441-940 1 Radiator Hose Tee

1441-941 1 Radiator Hose Wye

1441-942 7 Hose Clamp (12)

1441-943 4 Hose Clamp (20)

1441-944 4 Hose Clamp (3/8 in.)

1441-945 10 Cable Tie (14 in.)

1441-946 5 Cable Tie (7 in.)

1441-947 1 Cable Tie (4 in.)

1441-948 1 Switch

0541-853 1 Harness w/Fuse

1441-950 1 Formed Hose (3/4-in. (Twist))

1441-979 1 Formed Hose (3/4 x 9.375-in.)

1441-980 1 Formed Hose (3/4 x 8 1/2-in.)

1441-951 1 Coolant Hose (3/8-in x 18-in.)

1441-952 1 Fill Tee

1441-953 1 P-Clip

1441-954 1 Split Loom (1/4 in. x 12 in.)

1441-955 1 Split Loom (3/8 in. x 12 in.)

0123-010 4 Expansion Nut

1441-956 1 Coupling (3/4-in.)

0541-854 1 Coolant Pump

1441-957 1 Pump Coupling (3/4)

1441-958 1 Pump Coupling (3/8)

1436-408 1 Hardware Kit

0453-635 1 Instructions

 NOTE: Specific models may not have the under

hood storage assembly which must be ordered

and installed before installing this heater kit.

1. Remove the hood assembly and set aside. Retain

all hardware.

2. Secure Side Mounting Brackets (with flange to the

rear) to Heater so brackets are flush with heater

using four machine screws (included in Hardware

Kit). Tighten securely. See Fig. 1.

Fig. 1

ROV-049

3. Secure Right- and Left-Side Rear Mounting

Brackets to the top mounting locations of the side

mounting brackets (with brackets flush on the bot-

tom) using two screws and nuts (included in hard-

ware kit). See Fig. 2.

Fig. 2

ROV-050

4. Place heater into storage box so side mounting

brackets are approximately four inches below the

storage box lip and up against the operator’s-side

storage box wall. Mark all four mounting loca-

tions. See Fig. 3.

!WARNING

Allow the engine/cooling system to cool before

installing this kit.

Summary of content (5 pages)

PAGE 1
Form No. 0453-635 Arctic Cat® Prowler Installation Instructions - Accessory Kit Cab Heater Kit (p/n 1436-877)  NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain these Installation Instructions for future reference. Fig.
PAGE 2
Fig. 3 7. Insert adequate lengths of 2-in. Vent Hose into each opening; then while holding the heater, attach each vent hose to the heater flange (shown below) and secure with three Cable Ties (14 in.). See Fig. 6. Fig. 6 ROV-051 5. Using a 3/8-in. drill bit, drill all four locations; then install four Expansion Nuts. 6. On Prowlers without power steering, use a 2 1/4-in.
PAGE 3
11. Secure Coolant Pump (A) to the storage box using two self-tapping screws (shown below); then drill a 1-in. hole (B) into the storage box (operator’s side) directly across from the intake hose barb and secure coolant hose (3/8-in.) through drilled hole. See Fig. 8. 14. Locate and attach two Formed Hoses as shown with the Fill Tee (A) and secure with two clamps; then insert the Reducing Coupling (C) into the longest 90 degree Formed Hose (D), opposite the fill tee and attach to 5.
PAGE 4
Fig. 13 Fig. 16 ROV-315A 17. On models without a floor console, drill two holes in the splash panel using a two inch hole saw for the operator’s/passenger’s vents according to the illustration below; then pull the 2 inch vent hose from the “Y” fitting and secure to vents with cable ties (14 in.). Press vents in making sure they are fully seated. See Fig. 14. Fig. 14 ROV-318 21. Install floor console using existing hardware; then install console and seats. 22.
PAGE 5
Fig. 18 26. Using a 1/4-in. drill bit, drill a mounting location in the center of the storage box; then using P-Clip, secure the radiator hose to the storage box using a machine screw and nut. Remove the backing from the wire-tie mount (included in hardware kit) and adhere to the operator’s side of the storage box; then secure heater wires using one cable tie. See Fig. 20. Fig. 20 UTV-058 24. Attach the red wire to the jumped #1 and #3 posts on the back of the switch. 25.