Installation Guide

ManualsBrandsToro ManualsMulching & Striping42 in. Recycler Kit for TimeCutter MX 2015 Models

FormNo.3392-355RevB

42inRecycler

Kit

TimeCutter

MXSeriesRidingMower

ModelNo.131-4183

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Nopartsrequired

–

Removetheblades.

Bafeassembly

Kicker1

Flangenut(5/16inch)

Carriagebolt(5/16x3/4inch)

Kickerplate1

Self-tappingscrew(5/16x3/4inch)

Decal1

Installthekit.

Mulchingmowerblade2Installthebladesandmower.

WARNING

Whilemaintenanceoradjustmentsarebeingmade,

someonecouldstarttheengine.Accidentalstarting

oftheenginecouldseriouslyinjureyouorother

bystanders.

Removethekeyfromtheignitionswitch,engage

parkingbrake,andpullthewiresoffthesparkplugs

beforeyoudoanymaintenance.Pushthewires

asidesotheydonotaccidentallycontactthespark

plugs.

PreparingtheMower

NoPartsRequired

Procedure

1.Stoptheengineandremovetheignitionkey.

2.RemovethemowerasdescribedinyourOperator's

Manual.

3.Turnthemowerupsidedown.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3392-355*B

Summary of content (8 pages)

PAGE 1
Form No. 3392-355 Rev B 42in Recycler® Kit TimeCutter® MX Series Riding Mower Model No. 131-4183 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Use Qty. No parts required – Prepare the mower.
PAGE 2
4. Remove any debris and grass clippings from the underside of the deck. your mower. Hold the blade end using a rag or thickly-padded glove and remove the blade as shown. 5. Locate the cutoff baffle at the side-discharge opening on the mower deck (Figure 1). Figure 2 Blade style A mounting configuration G01801 1 1 Figure 1 1. Blade style A 4. Blade bolt 2. Cross section of blade style A 5. Curved washer 3. Blade stiffener required 6. Blade stiffener 1. Cutoff baffle (existing) 6.
PAGE 3
Installing the Kit Parts needed for this procedure: 1 Baffle assembly 1 Kicker 6 Flange nut (5/16 inch) 1. Kicker plate 1 Carriage bolt (5/16 x 3/4 inch) 2. Flange nut (5/16 inch) (4) 1 Kicker plate 2 Self-tapping screw (5/16 x 3/4 inch) 1 Decal Figure 5 3. Remove 2 plug bolts and 2 nuts here. 3. Secure the kicker plate to the left-hand side of the mower deck using 4 flange nuts (5/16 inch) as shown in Figure 5. 4. Tighten all fasteners. 5.
PAGE 4
A. Thoroughly clean the area where you will install the decal. Operation B. Dampen the area with water or mildly soapy water. C. Peel the decal from the backing and install it in place (Figure 7). Converting to Side-Discharge Operation D. Squeegee across the surface of the decal, starting at the center of the decal and working toward the edges, using overlapping strokes. 1. Reverse the steps in 4 Installing the Blades and Mower (page 4). 2. Reverse the steps in 3 Installing the Kit (page 2). 3.
PAGE 5
Cleaning after Operating To ensure optimum performance, clean the underside of the mower deck. Allowing the residue to build up in mower deck will decrease cutting performance.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8