Installation Instructions

ManualsBrandsToro ManualsUtility VehicleToro 127-8401

FormNo.3379-504RevB

DiagnosticCableKit

DDSeriesDirectionalDrillorRTSeriesTractionUnit

ModelNo.127-8401

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

Note:UsethiskitasadataconnectionbetweentheECU(electroniccontrolunit)onyourmachineandthecomputerthat

youwillusetoanalyzethecomponentfunctionsofthemachine.Inadditiontothiskit,youwillneed2softwareapplications

installedonyourcomputer:ThePlus+1GuideServiceToolcreatedbySauerDanfossandthesystemdiagnosticsoftware

createdbyTheToro®Company.

PreparingyourComputer

DownloadingthePlus+1GuideService

ToolSoftware

1.Onyourcomputer,navigatetotheToroCompany

PortalforPlus+1GUIDEServiceToolSoftware&

Licensetodownload.

2.NavigatetoGatewayPartsandServiceCenter.

3.ClicktheServiceLibrarytab.

4.ScrolltotheUndergroundEquipmenttab.

5.ClicktheDiagnosticSoftwarelink.

6.ClickthePlus+1GUIDEServiceToolSoftware&

Licenselinktodownloadit.

7.Whenthedownloadiscomplete,thePlus+1iconwill

appearonyourdesktop.

8.Onyourcomputer,navigatetotheToroCompany

PortalforthecorrectDiagnosticle.

9.NavigatetoGatewayPartsandServiceCenter.

10.ClicktheServiceLibrarytab.

11.ScrolltotheUndergroundEquipmenttab.

12.ClicktheDiagnosticSoftwarelink.

13.Clicktheproducttype.

14.Clickthemodelnumbertoobtainthecorrect

diagnosticle.

15.Savethediagnosticletoyourdesktop.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3379-504*B

Summary of content (4 pages)

PAGE 1
Form No. 3379-504 Rev B Diagnostic Cable Kit DD Series Directional Drill or RT Series Traction Unit Model No. 127-8401 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Installing the Toro System Diagnostic Software 2. Connect the 9-socket connector to the 9-pin connector of the diagnostic cable (Figure 2). This procedure describes how to installing the system diagnostic software from the Gateway Parts and Service Center website for the Toro Company. 1. Go to the Gateway Parts and Service Center. G024336 1 2 5 4 3 Figure 2 2. Open the Plus+1 GUIDE Service Tool. 3. Click on the diagnostic icon on the top tool bar. 4.
PAGE 3
1 G024350 Figure 4 Figure 6 1. Dust cap (DD4045 rear battery compartment) 1. Latch 4. Connector (3-pin adapter cable) 2. Diagnostic-port connector 5. Connector (diagnostic cable) 3. Adapter-harness plug (3 pin) B. Firmly insert the plug into the port until the latch of the diagnostic-port connector locks (Figure 6). • For a machine with a 9-socket diagnostic-port connector, connect it as follows: A.
PAGE 4
indicator light on the housing of the diagnostic cable illuminates (Figure 8). Note: When the adapter cable is connected to the diagnostic port of the machine and the diagnostic cable, and the control system of the machine is energized, the CAN indicator light on the housing of the diagnostic cable will illuminate (Figure 8). P WR CAN 1 2 G024335 Figure 8 1. PWR indicator light 2. CAN indicator light 7. Turn the master and ignition key switch to the on position.