Installation Instructions

ManualsBrandsToro ManualsGreens RollerSmoothing Roller Part Kit, GreensPro 1200 Greens Roller

FormNo.3383-774RevA

SmoothingRollerPartKit

GreensPro

™

1200GreensRoller

ModelNo.127-8002

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Removetheexistingrollers.

Presstool1Disassembletherollers.

Spacerdisc

Flockedbearingshield16

Bearing4

Longspacertube6

Shortspacertube

Bearinghousingassembly4

O-ring

Nut8

Assembletherollers.

Hex-headbolt8

Splitwasher

Washer8

Installtherollerassemblies.

RemovingtheExistingRollers

1.Raisethemachineupoffthegroundtoaccessthe

rollerassemblies.

2.Removethehex-headbolts,thewashers,andthesplit

washerssecuringthesidesoftherollerassembliesto

thesteeringheads(Figure1).

G025382

Figure1

1.Washer3.Hex-headbolt

2.Splitwasher

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3383-774*A

Summary of content (4 pages)

PAGE 1
Form No. 3383-774 Rev A Smoothing Roller Part Kit GreensPro™ 1200 Greens Roller Model No. 127-8002 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Remove the existing rollers. Press tool 1 Disassemble the rollers.
PAGE 2
Note: Take care not to press out the housing. 3. Remove the roller assemblies from the machine, and discard the bolts, washers, and split washers. E. Repeat steps C and D for the second roller half. Disassembling the Rollers 1. Remove the nuts from the ends of each roller assembly (Figure 2). 1 2 G025385 Figure 4 1. Inner bearing housing 2. Roller tube G025383 1 Figure 2 1. Nuts (existing) 2. Increase the gap (Figure 3) between the 2 roller tubes on each roller assembly.
PAGE 3
Note: Use the existing roller tubes and the existing inner bearing housings. A 1 B 2 Important: If necessary, press the existing bearing housing into the roller tube to seat it into position. 4. Install a bearing into the existing bearing housing in the roller tube (Figure 7). 1 2 3 G025348 Figure 10 2. Bearing housing assembly 1. O-ring 8. Install the bearing housing assembly (with an O-ring and a bearing) into the outer end of the roller tube (Figure 11). G025345 Figure 7 1.
PAGE 4
Installing the Roller Assemblies 1. Install the roller assemblies into the steering heads of the machine, and secure each end with a new hex-head bolt, a new split washer, and a new washer (Figure 1). Important: Align the short roller assemblies so that the short tubes are on the outside and the long tubes are on the inside (Figure 12). This staggers the joints between the roller tubes to improve the contact with the turf. 1 2 2 1 G025386 Figure 12 1. Joints 2. Short roller tube 2.