Use and Care Manual

ManualsBrandsToro ManualsOutdoor Power EquipmentSnow Cab Kit Accessory for Snow Blower

FormNo.3386-194RevB

SnowCabKit

PowerMaxSnowthrowers

ModelNo.127-5960

InstallationInstructions

WARNING

InstallingthissnowcabontoaPowerMax

snowthrowerwithoutproperlyinstallinga

counterweighttothefrontofthesnowthrowercan

causeittotipbackwardandfallontheoperator,

causinginjury.

•Donotoperateasnowthrowerwithasnowcab

thatdoesnothavethepropercounterweight.

•ObtainandinstallaToroweightkittothefront

ofthesnowthrowerinordertobalancetheadded

weightofthesnowcab.

InstallingtheSnowCabFrame

ontheSnowthrower

Partsneededforthisprocedure:

2U-bracket

4Washers

2Endcaps

Bolt(1/4x1inch)

Bolt(1/4x3/4inch)

Bolt(1/4x1-3/4inch)

Locknut(1/4inch)

Topframe

Rearframe

Horizontalframe

Leftmountingbracket

1Rightmountingbracket

2Frontposts

Procedure

1.Removethe2upperhandlenuts(1oneachside)from

thesnowthrowerhandleassembly(Figure1)andsave

themfor2.

Figure1

1.Handleassembly

4.Bolt,1/4x1-3/4inch(2)

2.Upperhandlenut(2)5.Locknut(2)

3.U-bracket(2)6.Leftmountingbracket

2.ForinstallationonHeavyDutyTwo-Stage

Snowthrowersonly:Installthelowerfrontendof

theleftandrightmountingbracketsontothehandle

assemblyusingtheupperhandlemountingnutsyou

removedin1(Figure1).

3.ForinstallationonCompactTwo-Stage

Snowthrowersonly:Installtheleftandrightspacing

bracket,theninstallthelowerfrontendoftheleftand

rightmountingbracketsontothehandleassembly

usingtheupperhandlemountingnutsyouremoved

in1(Figure2).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3386-194*B

Summary of content (8 pages)

PAGE 1
Form No. 3386-194 Rev B Snow Cab Kit Power Max Snowthrowers Model No. 127-5960 Installation Instructions WARNING Installing this snow cab onto a Power Max snowthrower without properly installing a counterweight to the front of the snowthrower can cause it to tip backward and fall on the operator, causing injury. • Do not operate a snowthrower with a snow cab that does not have the proper counterweight.
PAGE 2
7. Remove a locknut that you just installed on one of the front corners in 6, install the bottom (straight) end of a front post and a locknut onto the bolt, and tighten the locknut until the front post stays upright (Figure 4). Figure 2 1. Handle assembly 4. Bolt, 1/4 x 1-3/4 inch (2) 2. Upper handle nut (2) 5. Locknut (2) 3. U-bracket (2) 6. Left mounting bracket Figure 4 4.
PAGE 3
10. Position the rear frame with the top tabs facing forward and the bottom ends to the outside of the other frame ends (Figure 6). Figure 6 1. Locknut (2) 5. Horizontal frame 2. Washers (4) 6. Bolt, 1/4 x 1 inch (2) 3. Rear frame 7. End cap (2) Figure 7 1. Top frame 3. Bolt, 1/4 x 3/4 inch 2. Front post (2) 4. Locknut 4. Mounting bracket (2) 11. Install a washer and a locknut on each of the bolts and tighten each locknut until it is finger-tight. 12.
PAGE 4
Figure 9 1. Rear frame 2. Horizontal frame Figure 10 1. Headlight 15. Tighten all fasteners securely and insert the end caps on the bolt ends that extend from the washers (Figure 6). 3. Nut (2) 2. Bracket 2. Rotate the headlight bracket to the right 90 degrees (Figure 10) and tighten the nuts. 2 3. Install the headlight extension bar with a bolt (5/16 x 3/4 inch) and a flange locknut (5/16 inch) and secure the headlight to the bar (Figure 11).
PAGE 5
3 Installing the Cover Parts needed for this procedure: Cover Procedure 1. Open the 2 slits in the cover to allow room for the chute control rod and the headlight extension bar. 2. Slip the cover over the frame assembly and close the snaps to secure the cover around the top and rear frames (Figure 12). Figure 13 1. Cover Figure 12 1. Top flap 3. Top frame 2. Rear frame 4. Side flap 3. Close the slits around the chute control bar and headlight extension bar.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8