Product Manual

ManualsBrandsToro ManualsOutdoor Power EquipmentSnow Cab Kit Accessory for Snow Blower

 2003—The Toro Company

8111 Lyndale Ave., Bloomington, MN 55420, USA

Printed in the USA

Original Instructions (EN)

Snow Cab Kit

Power Max Snowthrowers

Model No. 107-3814

Form No. 3351-212

Installation Instructions

Save these instructions with your Operator’s Manual for

future reference.

Installing this snow cab onto a Power Max

snowthrower without properly installing a

counterweight to the front of the snowthrower can

cause it to tip backward and fall on the operator,

causing injury.

• Do not operate a snowthrower with a snow cab

that does not have the proper counterweight.

• Obtain and install a Toro weight kit to the front

of the snowthrower in order to balance the

added weight of the snow cab.

Warning

Contents of the Kit

DESCRIPTION QUANTITY

U-brackets 2

Washers 4

End caps 2

Headlight extension bar 1

Bolts, 1/4 x 1 in. 2

Bolts, 1/4 x 3/4 in. 6

Bolts, 1/4 x 1-3/4 in. 2

Locknuts, 1/4 in. 10

Bolt, 5/16 x 3/4 in. 1

Flange locknut, 5/16 in. 1

Top frame 1

Rear frame 1

Horizontal frame 1

Left mounting bracket 1

Right mounting bracket 1

Front posts 2

Cover 1

Installing the Snow Cab Frame

on the Snowthrower

1. Remove the 2 upper handle nuts (1 on each side) from

the snowthrower handle assembly (Fig. 1) and save

them for step 2.

m-7249

Figure 1

1. Handle assembly

2. Upper handle nut (2)

3. U-bracket (2)

4. Bolt, 1/4 x 1-3/4 in. (2)

5. Locknut (2)

6. Left mounting bracket

2. Install the lower front end of the left and right

mounting brackets onto the handle assembly using the

upper handle mounting nuts you removed in step 1

(Fig. 1).

3. Install the other lower end of each mounting bracket

onto the handle assembly with a U-bracket, bolt (1/4 x

1-3/4 in.), and locknut (Fig. 1).

Note: You may need to squeeze each U-bracket together

slightly before installing it onto the handle assembly.

Note: The ends of the U-brackets should face downward.

Summary of content (4 pages)

PAGE 1
Form No. 3351-212 Snow Cab Kit Power Max Snowthrowers Model No. 107-3814 Installation Instructions Save these instructions with your Operator’s Manual for future reference. Warning Installing this snow cab onto a Power Max snowthrower without properly installing a counterweight to the front of the snowthrower can cause it to tip backward and fall on the operator, causing injury. Installing the Snow Cab Frame on the Snowthrower 1.
PAGE 2
4. Position the horizontal frame inside the upper ends of the mounting brackets (Fig. 2). 7. Repeat step 6 for the other front post. 8. For each side, align the holes in the frame ends in the rear, insert a bolt (with a washer) through the holes from the inside (Fig. 4). Note: Position the horizontal frame with the 2 front tabs downward (see inset in Figure 3). 1 2 2 1 3 4 m-7250a Figure 2 1. Horizontal frame 2. Upper end of mounting bracket (4) 5.
PAGE 3
11. Hold the rear frame upright and tighten the locknuts (Fig. 5). 1 2 4 Note: Do not overtighten the locknuts because you will need to adjust the frame assembly to install the top frame and the cover. 12. Attach the top frame to the front posts (Fig. 6) and to the rear frame (Fig. 7) with 4 bolts (1/4 x 3/4 in.) and 4 locknuts. 3 3 m-2701 Note: Insert the bolts from the bottom. 1 4 3 2 m-7252a 1 Figure 7 m-2702 1. Locknut (2) 2. Rear frame 3. Top frame 4. Bolt, 1/4 x 3/4 in. 13.
PAGE 4
Installing the Headlight Extension Bar Installing the Cover 1. Open the 2 slits in the cover to allow room for the chute control rod and the headlight extension bar. If your snowthrower has a headlight, you will need to move the headlight. 2. Slip the cover over the frame assembly and close the snaps to secure the cover around the top and rear frames (Fig. 11). 1. Loosen the nuts that hold the headlight bracket onto the right side of the handle (Fig. 9). 1 1 3 2 2 4 m-7011 3 Figure 9 1.