Installation Instructions

ManualsBrandsToro ManualsTop DressersHitch Repair Kit, 2014 and before MH-400 Material Handler

FormNo.3386-944RevA

HitchRepairKit

2014andbeforeMH-400MaterialHandler

ModelNo.125-0147

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

WARNING

Thiskitrequirespartstobeweldedtothechassis.Weldingcanexposeyoutoanumberofhazards

includingtoxicfumes,smoke,dust,burns,res,explosions,electricshock,radiation,noise,andheat

stresswhichcancauseseriousinjuryanddeath.

•Weldingportionsofthekitshouldbeperformedbyacertiedwelder.

•Weldinaadequatelyventilatedareawithsuitablereextinguishingequipmentreadilyavailable.

•Weldinaresafeworkplace.Thiscanbeaccomplishedbyweldingbehindresafebarriersorcurtains

andonconcreteorotherresafeooring.Removeorprotectallcombustiblesfromignitionsources.

•Wearproperprotectiveclothingwhenwelding,suchasreretardantcoveralls.Protectyourhandswith

leathergauntletgloves.Feetshouldbeprotectedbyhightopleathershoes,preferablysafetyshoes.

•Protectyoureyeswhenwelding.Aweldinghelmetorhandshieldwithlterplateandcoverplateis

mandatorytoprotecttheeyeswhilewelding.Transparentgogglesorsafetyglassesshouldbeworn

atalltimes.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3386-944*A

Summary of content (4 pages)

PAGE 1
Form No. 3386-944 Rev A Hitch Repair Kit 2014 and before MH-400 Material Handler Model No. 125-0147 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. WARNING This kit requires parts to be welded to the chassis.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. No parts required – Prepare the frame. No parts required – Prepare the parts. Top right gusset Top left gusset Left side gusset Right side gusset 1 1 1 1 Back gusset 1 Install the back gusset No parts required – Paint the welds Note: Have a certified welder weld the components of kit together and onto the frame of the unit.
PAGE 3
4 Installing the Top Left and Right Gussets Installing the Right and Left side Gussets Parts needed for this procedure: Parts needed for this procedure: 1 Top right gusset 1 Left side gusset 1 Top left gusset 1 Right side gusset Procedure Procedure 1. Tack weld the plates in the locations shown in Figure 1. 1. Tack weld the plates in the locations shown in Figure 2. 3 2 1 4 3 .18 2 4 .18 2X g027347 Figure 2 2X 1. 1.27 cm (0.5 inch) 3. Side gusset 2. 1.27 cm (0.5 inch) 4.
PAGE 4
5 Installing the Back Gusset Parts needed for this procedure: 1 Back gusset Procedure 1. Tack weld the plate in the locations shown in Figure 3. 2. Weld the back gusset plates as shown in Figure 3. 1 2 3 .18 g027348 Figure 3 1. 1.27 cm (0.5 inch) 3. Weld 2. Back gusset 6 Painting the Welds No Parts Required Procedure 1. Allow for the welds to cool. 2. Clean up any spatter and sharp edges from the welds. 3. Prime and paint the area with touch-up paint. Note: Touch-up paint is not included.