Installation Instructions

ManualsBrandsToro ManualsLawn TractorsToro 121-4016

FormNo.3373-165RevB

HangerBracketUpgradeKit

2011-2012XLSLawnTractor

ModelNo.121-4016

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Hangerbracket,leftrear

Hangerbracket,rightrear1

Decksupportbracket2

Clevispin

Cotterpin

Shoulderbolt

Locknut2

Flatwasher2

Installthekit.

InstallingtheKit

1.Stoptheengine,waitforallmovingpartstostop,

andremovetheignitionkey.

2.Removethemowerdeckasdescribedinyour

Operator'sManual.

3.Removetheexistinghangerbracketsfromthedeck

brackets(

Figure1).

G018234

Figure1

1.Hangerbracket2.Deckbracket

Note:Savethehardwareforinstallingthenew

hangerbrackets.

4.ForModel71254only:Ifyouhavea38-inchmower

deck(formodel71254),youmustremovepartofthe

rearleft-handdeckbracketsothatthenewhanger

bracketwilltandallowthemowerdecktoberaised

orloweredfreely.Dothefollowingsteps:

A.Toaidinremovingmaterialfromtherear

left-handdeckbracket,drilla1/2-inch(13mm)

holeinthebracketatthelocationshownin

Figure2.

G018235

Figure2

1.Hangerbracket

4.5/8inch(16mm)

2.2inches(51mm)

5.Materialremoved

3.1/2–inch(13mm)hole

B.Removetheportionoftherearleft-handdeck

bracketasshowninFigure2.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3373-165 Rev B Hanger Bracket Upgrade Kit 2011-2012 XLS Lawn Tractor Model No. 121-4016 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. 1 1 2 2 2 2 2 2 Hanger bracket, left rear Hanger bracket, right rear Deck support bracket Clevis pin Cotter pin Shoulder bolt Locknut Flat washer Installing the Kit 1. Stop the engine, wait for all moving parts to stop, and remove the ignition key. 2.
PAGE 2
Note: File away sharp edges and burrs, and apply Toro touchup paint to any areas where bare metal has been exposed. 5. Install the new hanger brackets on the deck brackets as shown in Figure 3 and Figure 4. Note: Install the shoulder bolt through the upper hole in each hanger bracket (Figure 5). 1 4 5 1 4 4 2 3 6 3 2 3 7 G018236 Figure 3 Rear right-hand side shown from the left side G018238 1. Hanger bracket 3. Carriage bolt (existing) 2. Deck bracket 4.
PAGE 3
1 2 3 4 G018239 Figure 6 Rear lift rod not shown 1. Deck support bracket 3. Cotter pin 2. Flat washer 4. Clevis pin 8. Install the mowing deck and adjust both the side-to-side level and the front-to-rear blade slope. See the chapter on Blade Maintenance in the Operator’s Manual for the following procedures: Installing the Mower, Leveling the Mower from Side-to-Side, and Adjusting the Front-to-Rear Blade Slope.
PAGE 4