Use and Care Manual

ManualsBrandsToro ManualsMulching & StripingStriping Kit for 42 in. or 50 in. TimeCutter SS and Z Models

FormNo.3368-794RevB

StripingKit

for42inand50inMowers

ModelNo.120–7905

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Brackets

Rubbercaps

Speednut

Wiper1

Bolts(1/4x3/4inch)

Locknuts(1/4inch)

Washer

Stabilizerplate

Installthestripingkit.

RemovingtheMowerDeck

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurfaceanddisengage

thebladecontrolswitch.

2.Movethemotioncontrolleversoutwardtothe

parkposition,stoptheengine,removethekey,and

waitforallmovingpartstostopbeforeleavingthe

operatingposition.

3.Removethemowerdeckfromthemachine.Referto

theRemovingtheMowersectionintheOperator's

ManualortheappropriatesectionoftheService

Manual.

WARNING

Thespringisundertensionwheninstalledand

cancausepersonalinjury.

Becarefulwhenremovingthemowerbeltand

deck.

4.Slidethemowerdeckoutfromunderneaththe

machine.

5.Removethedeckspringfromtheidlerarm.

Important:Makenoteofthedeckspring

orientation.Itmustbeinstalledinthissame

hookendorientation.

OriginalInstructions(EN)PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3368-794 Rev B Striping Kit for 42in and 50in Mowers Model No. 120–7905 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 2 Description Brackets Rubber caps Speed nut Wiper Bolts (1/4 x 3/4 inch) Lock nuts (1/4 inch) Washer Stabilizer plate 1 Removing the Mower Deck No Parts Required Qty. 5 5 5 1 10 5 5 1 Use Install the striping kit. 4. Slide the mower deck out from underneath the machine. 5.
PAGE 2
Installing the Striping kit Parts needed for this procedure: 5 Brackets 5 Rubber caps 5 Speed nut 1 Wiper 10 Bolts (1/4 x 3/4 inch) 5 Lock nuts (1/4 inch) 5 Washer 1. Deck 3. Lock nut (1/4 inch) 1 Stabilizer plate 2. Bracket 4. Bolt (1/4 x 3/4 inch) Figure 2 Installing the Stripping Kit on 42 Inch Decks 4. Cut the wiper at the notch as shown below with a suitable tool such as tin snips or retractable blade. Use caution when cutting through the tough material (Figure 3). 1.
PAGE 3
Figure 4 1. Wiper, cut for 42 inch deck 4. Washer 2. Stabilizer plate 5. Bolt (1/4 x 3/4 inch) 3. Deck 6. Lock nut (1/4 inch) Figure 6 6. Install the wiper assembly to the brackets. Note: Reading the information included in Operation can help in choosing which set of holes, and in turn wiper height, to install wiper assembly at. 1. Deck 3. Bolt (1/4 x 3/4 inch) 2. Bracket 4. Lock nut (1/4 inch) 4. Install the wiper to the brackets (Figure 7).
PAGE 4
3 Installing the Mower No Parts Required Procedure Note: Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn mower belt. Replace the mower belt if any of these conditions are evident. Figure 9 Belt Routing, 50 inch Deck 1. Slide the mower under the machine. 2. Install the mower belt, if removed. Refer to the Replacing the Mower Belt section in the Operator's Manual. 3. Install the mower deck to the machine.
PAGE 5
Operation Striping visibility is affected by the sun position Adjusting the Height This is how the light is reflected on the grass. • Mowing patterns which generally run east–west will have a greater contrast than north–south patterns. • The striping pattern contrast is less visible around noon, and is more visible in mornings and afternoons. Important: Applying excessive downward pressure with the striping bar may damage turf and the striping kit.
PAGE 6
• Large areas with occasional trees or other obstructions will often look best when the mowing pattern appears to go through the obstruction. For example, it can look best for a pattern to match and continue on the far side of a small pond. A different cross cut pattern on the far side of a pond may not be visible. • Some areas look best with long straight lines of striping mowing pattern, aligned with a property edge.
PAGE 7
Notes: 7
PAGE 8