Installation Instructions

ManualsBrandsToro ManualsLawn TractorsToro 120-7760

FormNo.3368-776RevB

BeltGuardKit

XLS420TLawnTractor

ModelNo.120-7760

InstallationInstructions

Donotsupplytheseinstructionstothecustomer.

TheseinstructionsareforadealertoinstalladditionalbeltguardsonmachinessoldinFrance.

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocated

nearanyareaofpotentialdanger.

Replaceanydecalthatisdamagedor

lost.

93-6674

1.Crushinghazard,hand—readtheinstructionsbefore

servicingorperformingmaintenance.

120-1119

1.Firehazard—readtheOperator'sManual.

Installation

Note:Determinetheleftandrightsidesofthemachine

fromthenormaloperatingposition.

PreparingforInstallation

NoPartsRequired

Procedure

Important:Refertothe

Operator's Man ual

ifyou

areunfamiliarwiththespecicsofoperatingthis

machinebeforeproceeding.Themanualcontains

importantinformationaboutsafelyoperatingthe

machine.Ifyoudonotknowthisinformation,you

couldseriouslyinjureyourselforothers.

1.Parkthemachineonalevel,smoothsurfacewith

sufcientspacetoaccessbothsidesofthemowing

deck.

2.Levelthemowingdeck;seetheOperator’sManualfor

thismachine.

3.Lowerthemowingdecktotheshortestcutting

height.

WARNING

Beforeworkingonthemachine,stoptheengine,

settheparkingbrake,removetheignitionkey,

anddisconnectthesparkplugwire.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3368-776 Rev B Belt Guard Kit XLS 420T Lawn Tractor Model No. 120-7760 Installation Instructions Do not supply these instructions to the customer. These instructions are for a dealer to install additional belt guards on machines sold in France. Safety Installation Safety and Instructional Decals Note: Determine the left and right sides of the machine from the normal operating position.
PAGE 2
. Drill a hole for the right deck belt guard in the mowing deck as shown in Figure 2. CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition and disconnect the wire from the spark plug before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug. 4. Check the loose parts bag and verify that it contains all the parts listed in this document. 5.
PAGE 3
2 3 2 3 4 5 1 1 6 7 2 7 6 4 g016048 5 Figure 5 1. Locknut (NIM6-1) (2) g016047 Figure 4 1. Right deck belt guard 2. Flange nut, existing (2, one not shown) 3. Left deck belt guard 5. Hex bolt (M6-1X16), inserted from inside frame 6. Locknut (NIM6-1) 2. Washer (M6) (2) 5. Hex bolt (M6-1 X 16), inserted from below 6. Locknut (NIM6-1) 3. Hex bolt (M6-1X16), inserted from inside frame (2) 7. Open hole in left frame belt guard 4. Left frame belt guard 7. Washer (M6) 4.
PAGE 4
and that it will not interfere with the safe operation of the traction unit or the mowing deck. 4 Installing the Right Frame Belt Guard Parts needed for this procedure: Figure 8 1 Right frame belt guard 2 Hex bolt (M6-1X16) 2 Locknut (NIM6-1) 1. Hex bolt (M6-1X16), inserted from inside frame (2) 2. Procedure 3. Right frame belt guard Locknut (NIM6-1) (2) A. Loosen, but do not remove, the 2 existing bolts in the frame just behind the right front wheel. 1.