Installation Instructions

ManualsBrandsToro ManualsCommercial Debris BlowerWired Controller Kit, Pro Force Debris Blower

FormNo.3397-489RevA

WiredControllerKit

ProForce

DebrisBlower

ModelNo.119-1100

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

119-1775

1.Rotatenozzleleft4.Continuous-variable

setting

2.Rotatenozzleright5.Fast

3.Slow

119-1776

1.Engine—Stop3.Engine—Start

2.Engine—Run

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3397-489*A

Summary of content (8 pages)

PAGE 1
Form No. 3397-489 Rev A Wired Controller Kit Pro Force® Debris Blower Model No. 119-1100 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: Determine the left and right sides of the machine from the normal operating position.
PAGE 2
Description Qty. Use Wired controller 1 Install the wired controller—for Debris Blowers with serial numbers 290999999 and earlier.
PAGE 3
Installing the Wired Controller For Debris Blowers with Serial Numbers 310000001 to 311000001 1. Disconnect the battery cables from the battery. Note: Disconnect the negative-battery cable first, and then disconnect the positive-battery cable. 2. Disconnect the wire-harness leads from the wireless-control base (Figure 1). 3. Plug the appropriate wired-controller harness lead into the appropriate wire-harness lead that was previously disconnected from the wireless-control base (Figure 3 and Figure 4).
PAGE 4
Installing the Wired Controller 2 For Debris Blowers with Serial Numbers 31200000 to 315099999 (Model No. 44538, 44539, or 44542) 1 1. Disconnect the battery cables from the battery. 3 Note: Disconnect the negative-battery cable first, and then disconnect the positive-battery cable. g018908 Figure 6 2. Disconnect the wire harness from the wireless-control base (Figure 5). 1. Harness-adapter lead to the wireless control-base-harness lead 3.
PAGE 5
Installing the Wired Controller 4. Disconnect the wire harness from the key switch. 5. Remove the key switch (Figure 10). For Debris Blowers with Serial Numbers 315099999 and later (Model No. 44552, 44553, or 44554) 1. Disconnect the battery cables from the battery and remove the battery. Note: Disconnect the negative-battery cable first, and then disconnect the positive-battery cable. 2. Disconnect the wire-harness leads from the TEC controller (Figure 8). Figure 10 1. Key switch 6.
PAGE 6
Figure 12 1. Route the wire harness here. Figure 14 8. Plug the wireless-control-base lead into the harness adapter that was previously disconnected from the wireless-control base (Figure 13 and Figure 14). 1. Wire-harness adapter 2. Connect this wire-harness lead to the wire-harness adapter. Note: Ensure that you connect the leads into the proper connector color and internal notches. 3. Wireless TEC-controller-wire harness 4. Wireless TEC contoller 5. Yellow wire located by the hour meter 6.
PAGE 7
Operation Controls Using the Nozzle-Direction Button Press the button to rotate the nozzle to the desired direction (Figure 15). 1 2 3 g018877 Figure 15 1. Nozzle-direction button 3. Key switch 2. Throttle/engine-speed knob Using the Throttle/Engine-Speed Knob Rotate the knob to FAST to increase the engine speed, or to SLOW to decrease the engine speed (Figure 15). Using the Key Switch The key switch (which is used to start and stop the engine), has 3 positions: OFF, RUN, and START.
PAGE 8