Installation Instructions

ManualsBrandsToro ManualsLawn TractorsToro 112-5881

Form No. 3356-158 Rev B

Deck Belt Service Kit

For LX460 Tractors

Model No. 112-5881

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

Belt

Replace the upper deck belt.

Lower PTO lever

Flange locknut

Install the new lower PTO lever.

Important: R ead and under stand these instr uctions bef or e perf or ming the pr ocedur es

described. If y ou ar e not a trained and experienced ser vice and r epair technician, contact an

Authoriz ed Ser vice Dealer .

Note: Sa v e these instr uctions and refer to them when ordering re placement par ts .

Note: Deter mine the left and right sides of the mac hine from the operating position.

Step

Preparing for Service

No Parts Required

Procedure

1. Mo v e the tractor to lev el g round.

2. Shut off the engine , w ait for all mo ving par ts

to stop , and remo v e the ignition k ey .

3. Set the parking brak e .

4. Lo w er the mo w er dec k to the lo w est position.

5. Ensure that the PTO lev er is in the diseng ag ed

(Off) position.

6. Allo w the m ufﬂer and engine to cool.

Step

Removing the Deck

No Parts Required

Procedure

Important: R etain all hard w ar e or par ts

r emo v ed unless stated otherwise.

1. Use a 1/2-inc h soc k et and ratc het to loosen

the n ut that secures the left side of the engine

pulley belt guide to allo w the belt to clear the

guide ( Figure 1 ).

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (8 pages)

PAGE 1
Deck Belt Service Kit Form No. 3356-158 Rev B For LX460 Tractors Model No. 112-5881 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Step 3 5 Description Use Qty. Belt 1 Replace the upper deck belt. Lower PTO lever Flange locknut 1 2 Install the new lower PTO lever. Important: Read and understand these instructions before performing the procedures described.
PAGE 2
Figure 1 1. Belt guide nut 2. Engine pulley belt guide 2. Use a 1/4-inch socket and ratchet to remove the engine pulley belt guide. Figure 3 Note: Note in which hole the belt guide mounts for re-installation later. 1. Hairpin clip 2. Deck engagement cable 3. Cross brace slot 3. Remove the belt from the engine pulley. 7.
PAGE 3
Step Step 3 4 Replacing the Upper Deck Belt Removing the Lower PTO Lever Parts needed for this step: No Parts Required 1 Belt Procedure Procedure 1. Lift the engine hood. Note: Refer to Figure 4 for this procedure. 2. Drain the fuel tank or remove the fuel cap from the tank, place a piece of thin plastic ﬁlm over the mouth of the tank, and replace the fuel cap securely. 1. Use a 3/8-inch socket and ratchet to remove the 3 screws that secure the left belt cover from the cutting deck. 3.
PAGE 4
Watch that the fuel line connected to the fuel tank is not kinked, pulled from the fuel tank nipple, and that there is not stress placed on the nipple that would cause it to break. Figure 7 1. Shoulder bolt 2. Spring 3. 4. Lower PTO lever 7. Push up the lower PTO lever to slip the split plastic bushing out the hex hole in the frame. Figure 6 1. Steering column 2. Flange locknuts 3. 8. Push the plastic split bushing off the round section of the lower PTO lever shaft.
PAGE 5
Figure 8 1. Upper PTO lever 2. Stop engagement bracket 3. Lower PTO lever Figure 10 1. Hairpin clip 2. Screw and spacer 7. Connect the deck engagement cable loop end to the stud on the new lower PTO lever with the new cotter pin (Figure 9). Note: No ﬂat washer is required. 8. Insert the cotter pin and bend the cotter pin ends as shown in Figure 11. Figure 9 1. Lower PTO lever 3. 2. Flange locknut (2) 4.
PAGE 6
the PTO is in the engaged position, the unit is running, and the deck is engaged. 19. Remove the clevis pin and move the lift cable end loop to the hole indicated in Figure 12. Secure the lift cable with the clevis pin and cotter pin previously removed. Do not get your hands or feet near the cutting deck when the engine is running. 20. Repeat steps 16 through 19 for the other lift arm. 13. Shut off the engine.
PAGE 7
PAGE 8