Operator's Manual

ManualsBrandsToro ManualsVehiclesCab Kit, Workman GTX Utility Vehicle

FormNo.3432-927RevA

CabKit

Workman

GTXUtilityVehicle

ModelNo.07142—SerialNo.316000001andUp

ModelNo.07142—SerialNo.400000000andUp

Operator'sManual

Important:ThePowerConverterKitisrequired

tousethecabonaWorkmanGTXElectricutility

vehicle.ContactyourauthorizedTorodistributor

formoreinformation.

Important:TheSpringKitisrequiredtouse

thecabonaWorkmanGTXutilityvehicle.The

SpringKitshouldbeinstalledonlybyqualied

ToroServiceTechniciansusingapprovedtools.

Improperremoval,disassembly,orinstallationof

thespringassemblyposesadangertoyouand

bystanders.PleasecontactyourauthorizedToro

distributorfortheappropriatetoolsandproper

installationofthiskit.

Safety

WARNING

Thecompressedspringinthespringand

shockassemblyrepresentsastored-energy

hazard.Ifthespringisnotproperlyretained

duringcompressionorremoval,itcaninjure

youand/orbystanders.

•AlwaysusetheapprovedToro

spring-compressiontooltocompressthe

springinasecurepositionwhenremoving

theretentioncollar.

•Alwaysusecarewhenremovingpressure

fromthecompressedspring.

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal133-1016

133-1016

1.Warning—readthe

Operator'sManual;wear

theseatbelt,andavoid

tippingthemachine.

2.Warning—wearhearing

protection.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3432-927*A

Summary of content (16 pages)

PAGE 1
Form No. 3432-927 Rev A Cab Kit Workman® GTX Utility Vehicle Model No. 07142—Serial No. 316000001 and Up Model No. 07142—Serial No. 400000000 and Up Operator's Manual Important: The Power Converter Kit is required to use the cab on a Workman GTX Electric utility vehicle. Contact your authorized Toro distributor for more information. Important: The Spring Kit is required to use the cab on a Workman GTX utility vehicle.
PAGE 2
decal130-5964 130-5964 1. Warning—in the event of an emergency 1) Pull the locking pin out of each hinge; 2) Push the front window out to exit. decal133-1017 133-1017 1. Do not repair or revise—read the Operator's Manual. decal131-8410 131-8410 1. Fire hazard—shut off the engine before fueling. decal120-9570 120-9570 1. Warning—stay away from moving parts, keep all guards and shields in place. decal130-5439 130-5439 1. Read the Operator’s Manual for information on fuses. 4. Windshield spray 2.
PAGE 3
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 2 No parts required – Prepare the machine. No parts required – Remove the strut assembly (for 2018 and before machines only). 3 Spring 2 Install the springs (for 2018 and before machines only). 4 No parts required – Install the strut assembly (for 2018 and before machines only).
PAGE 4
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface, set the parking brake, shut off the engine, and remove the key. 2. Raise the bed until the bed prop rod is fully engaged; refer to the Operator’s Manual for the machine. 3. Remove the seat base. 4. Disconnect the negative battery cable; refer to your Operator’s Manual. 2 Removing the Strut Assembly For 2018 and Before Machines Only No Parts Required Procedure 1. Remove the front wheel. 2.
PAGE 5
g038284 Figure 1 Hood and fender not shown to show the shock-mount bracket 1. Hex-head bolt (1/2 x 2-1/4 inches) 6. Flange nut (3/8 inch)—from the control arm 2. Locknut (1/2 inch) 7. Flange nut (3/8 inch)—from the spindle 3. Collar 8. Hex-head bolt (3/8 x 3-1/2 inches)—from the control arm 4. Spring 9. Hex-head bolt (3/8 x 4-3/4 inches)—from the spindle 5.
PAGE 6
3 4 Installing the Springs Installing the Strut Assembly For 2018 and Before Machines Only For 2018 and Before Machines Only Parts needed for this procedure: 2 Spring No Parts Required Procedure Procedure Use an approved Toro spring-compression tool to remove and install springs of the strut assembly. Contact your authorized Toro distributor. 1. Install strut assembly to the machine. 2.
PAGE 7
2. 5 Use a floor jack under the frame to support the front of the machine (Figure 3). Installing the Supports Parts needed for this procedure: 2 Floor-plate support 16 Flange-head bolt (5/16 x 1-1/4 inches) 16 Flange nut (5/16 inch) 1 Left cab support 1 Right cab support 4 Hex-head bolt (3/8 x 1-1/4 inch) 4 Flange nut (3/8 inch) 4 Washer (3/8 inch) g038334 Figure 3 1. Frame 3. Procedure 1. Remove 1 of the existing floor-plate supports (Figure 4).
PAGE 8
4. 8. Install a new floor-plate support using 8 flange-head bolts (5/16 x 1-1/4 inches) and 8 flange nuts (5/16 inch) as shown in Figure 5. Using the new floor-plate supports as a guide, drill 3 holes (3/8-inch diameter) into each floor plate (Figure 6). Important: Drill only the front 2 holes on the new floor-plate supports and the farthest, rear hole; as shown in Figure 6. Note: Torque the flange-head bolts (5/16 x 1-1/4 inches) to 34 N∙m (25 ft-lb). g035247 Figure 5 1. Flange nut (5/16 inch) 3.
PAGE 9
3. 6 Remove the 3 screws and 3 nuts securing the left handhold, and remove it (Figure 9).
PAGE 10
5. Lift the cab frame using the lift points and place it on the machine (Figure 11). 7. Secure the back of the cab frame to the left and right supports using 4 flange-head bolts (5/16 x 1-1/4 inches), 2 support plates, 4 flat washers, and 4 flange nuts (5/16 inch) as shown in Figure 13. Note: Torque the bolts to 34 N∙m (25 ft-lb). g037103 Figure 11 1. Lift points 6.
PAGE 11
. Install the seat base. Note: You may need to position the 2 center seat-belt anchors to allow the seat to drop into place. Loosen the 2 locknuts (7/16 inch) on the 2 center seat-belt anchors, and tighten the 2 locknuts (7/16 inch) to 72 to 88 N∙m (53 to 65 ft-lb) after adjusting the position. 12. Remove the backing from the right, front and left, front foam seals and attach the seals to the machine (Figure 15). g035254 Figure 15 1. Left, front foam seal 13.
PAGE 12
• For 2019 and after machines, secure the 7 new fuse block using the 2 hex-washer head screws (#10 x 3/4 inch) and 2 serrated nuts (#10) as shown in Figure 18.
PAGE 13
4. Route the wire harness behind the cab and under the seat, and secure the clip on the wire harness to the side panel (Figure 19). g035260 Figure 19 1. Wire harness 5. Install the black ground wire to the ground wire on the Power Converter Kit wire harness (Figure 20). Note: The black terminal ring is not used. 6. Install the red power wire to the power wire on the Power Converter Kit wire harness (Figure 20). g278776 Figure 20 1. Cab wire harness 3. Black ground wire with spade terminal 2.
PAGE 14
For Gasoline/Petrol or EFI Machines 1. Install the new fuse block as follows: 4. Install the black terminal ring to the ground block on the machine (Figure 22). 5. Install the red power wire into an empty slot on the machine fuse block (Figure 22). • For 2018 and before machines, snap the Note: Install an additional fuse block if there are no remaining slots open in a fuse block. new fuse block onto the existing fuse block on the machine (Figure 17).
PAGE 15
Product Overview Controls Control Panel Windshield-Wiper Switch Click the switch forward to activate the windshield wipers (Figure 23). g026274 Figure 23 1. Windshield-wiper control 2. Light switch Light Switch Push the left or right side of the light plate to turn on the cab light (Figure 23). Windshield Latch Lift up on the latches to open the windshield (Figure 24). Press down on the latch to lock the windshield in the open position.
PAGE 16
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Conditions and Products Covered Parts The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).