Installation Instructions

ManualsBrandsToro ManualsVehiclesCanopy Kit, 4-passenger Workman GTX Utility Vehicle

Table Of Contents

.
- 1 Preparing the Machine
- 2 Installing the Kit

FormNo.3406-327RevA

CanopyKit

Multi-PassengerWorkman

GTXUtilityVehicle

ModelNo.07141—SerialNo.316000501andUp

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface,settheparking

brake,shutofftheengine,andremovethekeyfrom

theignitionswitch.

2.Removetherearseats.

3.Raisethecargoboxtothedumpposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-327*A

Summary of content (8 pages)

PAGE 1
Form No. 3406-327 Rev A Canopy Kit Multi-Passenger Workman® GTX Utility Vehicle Model No. 07141—Serial No. 316000501 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation 1 Preparing the Machine No Parts Required Procedure 1.
PAGE 2
Procedure 2 Note: Do not tighten any fasteners except when instructed. 1. Install the left loop bracket as follows: Installing the Kit A. Remove the rivet from left panel behind the rear seat base (Figure 1). Parts needed for this procedure: B. Install the left loop bracket using 2 hex-flange bolts (3/8 x 1 inch) and 2 nuts (3/8 inch) as shown in Figure 1.
PAGE 3
. Using the dimensions shown in Figure 4, drill 1 hole (5/16 inch) into the outside of the footboard on the left and right sides of the machine. Figure 2 1. Flange nut (1/4 inch) 4. Hex-head bolt (1/4 x 2-1/2 inches) 2. Spacer (9/32 x 5/8 inch) 5. Flat washer (5/16 inch) 3. Left loop bracket D. Figure 4 Repeat this step to install the right loop bracket on the right side of the machine. 4.
PAGE 4
5. Secure the lower bracket of the windshield support to the left side of the machine using 4 carriage bolts (5/16 x 1 inch) and 4 flange nuts (5/16 inch) in the holes you drilled in step 2 (Figure 6). 7. Loosely install the left and right rear plates to the tubes using 4 carriage bolts (5/16 x 1-3/4 inches), 2 backing plates, and 4 flange nuts (5/16 inch) as shown in Figure 8. Figure 6 1. Carriage bolt (5/16 x 1 inch) Figure 8 3. Lower bracket of windshield support 2. Flange nut (5/16 inch) 1.
PAGE 5
9. Loosely install the rear crosslink to the crosslink tubes and rear plates using 4 carriage bolts (5/16 x 1-3/4 inches), 4 carriage bolts (5/16 x 3/4 inch), and 8 flange nuts (5/16 inch) as shown in Figure 10. 11. Tighten all loose fasteners. 12. Install the 2 roof-support brackets to the crosslink tubes using 2 self-tapping screws (1/4 x 1/2 inch) as shown in Figure 12. Figure 12 Figure 10 1. Carriage bolt (5/16 x 3/4 inch) 3. Carriage bolt (5/16 x 1-3/4 inches) 2. Rear crosslink 4.
PAGE 6
15. Install the sunshade to the roof-support bracket using 2 clips, 2 sealing washers, and 2 hex-flange bolts (1/4 x 1 inch) as shown in Figure 14. 17. Install the sunshade to the rear crosslink using 2 hex-flange bolts (1/4 x 1 inch), 2 sealing washers, 2 friction washers, 4 plastic washers, and 2 flange bushings (Figure 16). Important: Apply thread-locking compound to the hex-flange bolts (1/4 x 1 inch) before installing.
PAGE 7
Notes:
PAGE 8
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).