Installation Instructions

ManualsBrandsToro ManualsVehiclesCanopy Kit, Workman GTX Utility Vehicle

FormNo.3407-127RevA

CanopyKit

Workman

GTXUtilityVehicle

ModelNo.07140—SerialNo.316000001andUp

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface,settheparking

brake,shutofftheengine,andremovethekeyfrom

theignitionswitch.

2.Removetheseats.

3.Raisethecargoboxtothedumpposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3407-127*A

Summary of content (8 pages)

PAGE 1
Form No. 3407-127 Rev A Canopy Kit Workman® GTX Utility Vehicle Model No. 07140—Serial No. 316000001 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface, set the parking brake, shut off the engine, and remove the key from the ignition switch. 2.
PAGE 2
Procedure 2 Note: Do not tighten any fasteners except when instructed. 1. Install the left loop bracket as follows: A. Remove the rivet from left panel behind the rear seat base (Figure 1). B. Install the left loop bracket using 2 hex-flange bolts (3/8 x 1 inch) and 2 nuts (3/8 inch) as shown in Figure 1.
PAGE 3
D. Repeat this step to install the right loop bracket on the right side of the machine. 4. Secure the middle bracket of the windshield support to the machine using 2 hex-flange bolts (5/16 x 1 inch) and 2 nuts (5/16 inch) in the holes you drilled (Figure 5). 2. Using the dimensions shown in Figure 3, drill 2 holes (5/16 inch) into the outside of the floor plate on the left and right sides of the machine. Figure 5 1. Windshield support 3. Nut (inside dash frame) 2. Hex-flange bolt Figure 3 5.
PAGE 4
6. Loosely install the rear tubes to the rear loop brackets using 8 carriage bolts (5/16 x 2 inches), 2 mounting plates, and 8 nuts (5/16 inch) as shown in Figure 7. 8. Loosely install the left and right front plates and corner gussets to the crosslink tubes and the left and right windshield supports using 8 carriage bolts (5/16 x 1-3/4 inches) and 8 flange nuts (5/16 inch) as shown in Figure 9. Figure 9 Figure 7 1. Carriage bolt (5/16 x 2 inches) 1. Carriage bolt (5/16 x 1-3/4 inches) 4.
PAGE 5
10. Loosely install the front crosslink to the front plates and corner gussets using 4 carriage bolts (5/16 x 1-3/4 inch) and 4 flange nuts (5/16 inch) as shown in Figure 11. 13. Install the sunshade to the rear crosslink using 2 hex-flange bolts (1/4 x 1 inch), 2 sealing washers, 2 friction washers, 4 plastic washers, and 2 flange bushings (Figure 13). Important: Apply thread-locking compound to the hex-flange bolts (1/4 x 1 inch) before installing.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).