Form No. 3390-360 Rev A Finger Deck Versa-Vac Model No. 07081—Serial No. 315000001 and Up Register at www.Toro.com.
Contents This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. Safety ........................................................................... 3 Before Operating .................................................... 3 Operating............................................................... 3 Maintenance ........................................................... 3 Safety and Instructional Decals ......
Safety – Before backing up, look to the rear and ensure that no one is behind the machine. Hazard control and accident prevention are dependent upon the awareness, concern, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the machine. Improper use or maintenance of the machine can result in injury or death. To reduce the potential for injury or death, comply with the following safety instructions. – Watch out for traffic when near or crossing roads.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 105-4586 1. Entanglement hazard, belt—stay away from moving parts. Do not operate the machine with the shields or guards removed; keep the shields and guards in place. 106-0177 106-0178 106-0188 1. Cutting hazard of hand or foot—wait for moving parts to stop.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. – No parts required Install the finger deck. Media and Additional Parts Description Use Qty. Parts Catalog 1 Use to reference part numbers Operator's Manual 1 Review the manual and save in an appropriate place Registration card 1 Fill out and return to Toro. Note: Determine the left and right sides of the machine from the normal operating position. Installing the Finger Deck 1.
Product Overview Note: Verify that the fingers rotate. The fingers should rotate clockwise (as viewed from the motor end of the deck). Specifications Width 193 to 203 cm (76 to 80 inches) Operating Width 183 cm (72 inches) Height 40.6 to 61 cm (16 to 24 inches) Weight 117 to 140 Kg (258 to 308 lb) Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities.
Operation • Always try to make a long, continuous run with a slight Note: Determine the left and right sides of the machine from the normal operating position. • On turf areas, the deck will pick up twigs, clippings, overlap on the return run. leaves, pine needles, pine cones, and small debris. Important: Do not make sharp turns when using the machine as damage to turf may occur. Checking the Tire Pressure Important: Do not operate the machine while the rotor is turning and in the raised position.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 20 hours • Check and adjust the drive belt. Before each use or daily • Check the tire pressure. • Clean the machine. • Grease the machine. After each use Greasing the Machine Service Interval: After each use The deck has 10 grease fittings that must be lubricated regularly with No. 2 General Purpose Lithium Base Grease.
5. Insert the bolt into the aligned guide holes and secure it with the nut. If holes are not exactly aligned, rotate the guide to the next higher hole until aligned. 6. Tighten the bolt on the back side of the frame to lock the tensioner. 7. Install the motor shield. Replacing the Finger Belts 1. Loosen the nuts and washers securing the finger pinchers to rotor (Figure 11 and Figure 12). 2. Remove the old belt fingers. 3. Install new belt fingers (Figure 11 and Figure 12).
Figure 12 1. Approximately 10 cm (4 inches) 3. Keyed shaft 2. Flat side of the belt 4.
Declaration of Incorporation The Toro Company, 8111 Lyndale Avenue South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. Serial No.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
