Installation Instructions

ManualsBrandsToro ManualsVehiclesCargo Bed Kit, Workman GTX Utility Vehicle

FormNo.3450-829RevA

CargoBedKit

Workman

GTXUtilityVehicle

ModelNo.07046

InstallationInstructions

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

damage.Replaceanydecalthatis

damagedormissing.

decal115-7739

115-7739

1.Falling,crushinghazard—donotcarrypassengers.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Rightcargobedsupport1

Leftcargobedsupport

Flange-headbolt(5/16x3/4inch)

Washer8

Installthecargobedsupports.

Proprodbracket1

Hex-headbolt(3/8x2-1/2inches)

Locknut(3/8inch)

Installtheproprodbracket(forserial

410500000andafter).

Bolt(1/2x4-1/2inches)

Flangenut2

Installthecargobed.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3450-829*

Summary of content (8 pages)

PAGE 1
Form No. 3450-829 Rev A Cargo Bed Kit Workman® GTX Utility Vehicle Model No. 07046 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential damage. Replace any decal that is damaged or missing. decal115-7739 115-7739 1. Falling, crushing hazard—do not carry passengers. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the machine and remove the key. g038447 Figure 1 2 Installing the Cargo Bed Supports Parts needed for this procedure: 1 Right cargo bed support 1 Left cargo bed support 8 Flange-head bolt (5/16 x 3/4 inch) 8 Washer Procedure 1. Align the holes in each of the cargo bed supports to the threaded inserts on the bottom of the cargo bed (Figure 2). 2.
PAGE 3
g322754 Figure 2 1. Right cargo bed support 3. Washer 2. Flange-head bolt (5/16 x 3/4 inch) 4.
PAGE 4
3 Installing the Prop Rod Bracket For Serial 410500000 and After Parts needed for this procedure: 1 Prop rod bracket 2 Hex-head bolt (3/8 x 2-1/2 inches) 2 Locknut (3/8 inch) Procedure 1. Secure the prop rod bracket to the machine frame using 2 hex-head bolts (3/8 x 2-1/2 inches) and 2 locknuts (3/8 inch) as shown in Figure 3. 2. Torque the 2 hex-head bolts (3/8 x 2-1/2 inches) to 41 N∙m (30 ft-lb). g377340 Figure 3 1. Prop rod bracket 3. Hex-head bolt (3/8 x 2-1/2 inches) 2.
PAGE 5
. 4 Swing the prop rod forward and insert the short leg of the rod through the key hole (Figure 5). Installing the Cargo Bed Parts needed for this procedure: 2 Bolt (1/2 x 4-1/2 inches) 2 Flange nut Procedure 1. g191980 Figure 5 Park the machine on a level surface, engage the parking brake, shut off the machine, and remove the key. 1. Prop rod 2. Rotate the cargo bed so that the pivot-bracket assembly and prop rod are facing downward. 6. 3.
PAGE 6
5 Adjusting the Cargo-Bed Latches No Parts Required g034021 Procedure Figure 8 If the cargo-bed latch is out of adjustment, the cargo bed vibrates up and down as you drive the machine. You can adjust the latch posts to make the latches hold the cargo bed securely to the chassis. 1. 1. Service position detent slot 2. Prop rod Verify that the cargo bed is latching. 4. Note: If the cargo bed does not latch, the bed-latch striker is likely too low.
PAGE 7
Notes:
PAGE 8