Form No. 3437-810 Rev C Workman® GTX Electric Utility Vehicle Model No. 07043—Serial No. 403448001 and Up Model No. 07131TC—Serial No. 403448001 and Up Model No. 07153—Serial No. 402590001 and Up Register at www.Toro.com.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Contents Maintaining the Headlights ............................... 39 Drive System Maintenance .................................. 40 Maintaining the Tires ........................................ 40 Inspecting the Steering and Suspension Components ................................................. 41 Adjusting the Front Wheel Alignment ................ 41 Checking the Transaxle-Fluid Level .................. 42 Changing the Transaxle Fluid ........................... 43 Brake Maintenance .................
Safety This machine has been designed in accordance with the requirements of SAE J2258 (Nov 2016). General Safety This product is capable of causing personal injury. Always follow all safety instructions to avoid serious personal injury. • Read and understand the contents of this Operator’s Manual before you start the machine. Ensure that everyone using this product knows how to use it and understands the warnings. • Use your full attention while operating the machine.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal99-7345 99-7345 1. Warning—read the Operator's Manual. 2. Warning—do not touch the hot surface. 3. Entanglement hazard, belt—stay away from moving parts; keep all guards in place. 4. Crushing hazard, cargo box—use the prop rod to support the cargo bed. decal115-7739 115-7739 1.
decal131-8495 131-8495 decal131-8414 131-8414 1. Warning—read the Operator's Manual. 3. Tipping hazard—drive slowly across or up slopes; take turns slowly; do not exceed speeds of 25 kph (16 mph); drive slowly when hauling cargo; drive slowly on uneven terrain. 2. Warning—receive proper training before operating the machine. 4.
200 LBS 91 KG 1500 LBS 680 KG 137-9984 decal137-9984 137-9984 1. Do not exceed a tongue weight of 91 kg (200 lb). 2. Do not exceed a transport load of 680 kg (1,500 lb). decal131-8527 131-8527 1. Performance mode 2. Eco mode decal138-3525 138-3525 1. Light—On 3. Raise the bed. 2. Light—Off 4. Lower the bed. decal139-3338 139-3338 5. Electric (10 A) 1. Read the Operator’s Manual for fuse information. 2. Horn (30 A) 6. Headlights (10 A) 3. Electric relay (20 A) 7.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Qty. Use Steering wheel Steering wheel cover Washer (1/2 inch) Dust cover 1 1 1 1 Install the steering wheel (International models only). No parts required – Check the fluid levels and tire pressure. No parts required – Burnish (break-in) the brakes.
2 4 Checking the Fluid Levels and Tire Pressure Reading the Manual and Viewing the Setup Material No Parts Required Parts needed for this procedure: Procedure 1. Check the water level in the batteries before you operate the machine; refer to Checking the Water Level of the Batteries (page 37). 2. Ensure that the batteries are charged; refer to Charging the Batteries (page 35). 3. Check the brake-fluid level before you operate the machine; refer to Checking the Brake-Fluid Level (page 44). 4.
Product Overview g034154 Figure 4 1. Hood latch 3. Cargo bed 5. Battery charger 2. Steering wheel 4. Towing tongue 6. Cargo-bed lever g034544 Figure 5 1. Passenger handhold 3. Rear cargo-bed-accessory mount 2. Parking-brake lever 4.
Controls Become familiar with all the controls before you start the engine and operate the machine. Control Panel g034161 Figure 6 1. Light switch 7. Parking-brake lever 2. Hour meter 8. Brake pedal 3. Battery-discharge indicator 9. Accelerator pedal 4. Horn button (International models only) 10. USB power point 5. Gear-shift selector 11. Status-indicator light 6. Key switch Accelerator Pedal Brake Pedal Use the accelerator pedal (Figure 6) to vary ground speed of the machine.
Parking-Brake Lever Direction Selector The parking-brake lever is located on the control panel (Figure 6). The direction selector is located to the left of the parking-brake lever. The direction selector has 3 positions: FORWARD , REVERSE, and NEUTRAL (Figure 6). Whenever you shut off the machine, engage the parking brake to prevent the machine from accidentally moving. If the machine is parked on a steep grade, ensure that you engage the parking brake.
Key Switch Status-Indicator Light Use the key switch (Figure 6), to run and shut off the machine. The status-indicator light is located to the right of the parking-brake lever on the control panel (Figure 6). The key switch has 2 positions: ON and OFF. Rotate the key clockwise to the ON position to operate the machine. When you stop the machine, rotate the key counterclockwise to the OFF position to shut off the machine. Remove the key whenever you leave the machine.
Specifications Note: Specifications and design are subject to change without notice.
Operation smoother ride, and to minimize tire marks on the ground. • Use higher air pressure in the tires for Before Operation carrying heavier payloads at higher speeds. 2. Before Operation Safety If necessary, adjust the air pressure in the tires by adding or removing air in the tires. General Safety • Never allow children or people who are not trained or physically capable to safely operate or service the machine. Local regulations may restrict the age of the operator.
Using the Battery System a break-in period to establish efficient electrical production. This break in period usually requires 100 to 150 discharge/charge cycles. When your batteries are fully charged, the tenth bar (far right) illuminates on the battery-discharge indicator (Figure 13). g004049 Figure 12 Battery-Lifetime Table 1. Battery capacity 4. Prime battery life 2. Discharge/charge cycles 5. End of the battery life 3.
If you continue to use the machine with only 2 bars remaining, bars 1 and 2 alternately flash. During Operation Important: When only the second bar from the During Operation Safety left remains on the battery-discharge indicator, the machine may enter a reduced-speed mode; this mode aids in protecting the batteries, but prolonged operation in this mode can damage the batteries and/or the machine. Avoid draining your batteries down to the second bar from the left to prevent this issue.
• • • • • • • • • • • • • You and your passengers should remain seated when approaching blind corners, shrubs, trees, or other objects that may obscure your vision. Do not drive the machine near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge gives way. Always watch out for and avoid low overhangs such as tree limbs, door jambs, overhead walkways, etc. Look behind and down before reversing the machine to be sure of a clear path.
Loading and Dumping Safety 1. • Do not exceed the gross vehicle weight (GVW) • • • Pull the lever on left, inside of the cargo bed toward you and lift the cargo bed up (Figure 15). of the machine when operating it with a load in the cargo bed and/or towing a trailer; refer to Specifications (page 14). Distribute the load in the cargo bed evenly to improve the stability and control of the machine. Before dumping, ensure that there is no one behind the machine.
Opening the Tailgate Raising the Cargo Bed to the Service Position 1. Ensure that the cargo bed is down and latched. 1. Pull the lever on left, inside of the cargo bed toward you and lift the cargo bed up (Figure 15). 2. Using both hands, raise the tailgate using the ridge near the top of the tailgate (Figure 17). 2. Pull prop rod into the service position detent slot to secure the bed for maintenance (Figure 16). 3.
Closing the Tailgate Using the Rear Cargo Bed Accessory Mount If you unloaded loose material such as sand, landscaping rock, or wood chips from the cargo bed of the machine, some of the material that you unloaded may have lodged in the hinge area of the tailgate. Perform the following steps before closing the tailgate. 1. Use your hands to remove as much of the material from the hinge area as possible. 2. Rotate the tailgate to approximately the 45° position (Figure 18).
Stopping the Machine • Whenever possible, secure the load by binding it Important: When stopping the machine on • When transporting liquids, use caution when to the cargo bed so that it does not shift. an incline, use the service brakes to stop the machine and engage the parking brake to hold the machine in place. Using the accelerator to stall the machine on the hill can overheat the motor or drain the batteries. 1. Remove your foot from the accelerator pedal. 2.
After Operation After Operation Safety General Safety • Before you leave the operating position, do the following: – Park the machine on a level surface. – Move the direction selector to the NEUTRAL position. g236535 Figure 21 – Engage the parking brake. 1. Towing tongue and tie-down point (front of the machine) – Shut off the machine and remove the key. – Wait for all movement to stop. • Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Towing the Machine In case of an emergency, you can tow the machine for a short distance; however, this should not be a standard operating procedure. WARNING Towing at excessive speeds could cause a loss of steering control, resulting in personal injury. Never tow the machine at faster than 8 km/h (5 mph). Towing the machine is a 2-person job. If you must move the machine a considerable distance, transport it on a truck or trailer; refer to Towing a Trailer (page 24). 1.
Maintenance Maintenance Safety • If possible, do not perform maintenance while the machine is running. Keep away from moving parts. • Do not allow untrained personnel to service the • • • • • • • machine. Before you leave the operating position, do the following: – Park the machine on a level surface. – Move the direction selector to the NEUTRAL position. – Engage the parking brake. – Shut off the machine and remove the key. – Wait for all movement to stop.
Maintenance Service Interval Maintenance Procedure Every 400 hours • Replace the service and parking-brake pads. Every 800 hours • Change the transaxle fluid. Every 1,000 hours • Change the brake fluid. Note: Download a free copy of the electrical schematic by visiting www.Toro.com and searching for your machine from the Manuals link on the home page. WARNING Failure to properly maintain the machine could result in premature failure of machine systems, causing possible harm to you or bystanders.
Maintaining the Machine under Special Operating Conditions Important: If the machine is subjected to any of the conditions listed below, perform maintenance twice as frequently: • Desert operation • Cold climate operation—below 10°C (50°F) • Trailer towing • Frequent operation in dusty conditions • Construction work • After extended operation in mud, sand, water, or similar dirty conditions, do the following: – Have your brakes inspected and cleaned as soon as possible.
Lifting the Machine DANGER The machine may be unstable when using a jack. The machine could slip off the jack, injuring anyone beneath it. • Do not start the machine while the machine is on a jack. g034407 Figure 24 • Always remove the key from the key switch before getting off the machine. 1. Rear lifting points • Block the tires when the machine is supported by lifting equipment. Accessing the Hood • Use jack stands to support the machine once you have lifted it.
Raising and Lowering the Seat Assembly To raise the seat assembly, push the seat assembly forward until it rests on the steering wheel (Figure 26). To lower the seat assembly, push the seat assembly rearward until it seats back into the original position (Figure 26). g190187 Figure 27 1. Pins Installing a Bucket Seat Slide the seat assembly onto the pins and lower the seat assembly (Figure 28). g190066 Figure 26 Removing a Bucket Seat 1.
Lubrication Greasing the Front Wheel Bearings Greasing the Machine Service Interval: Every 300 hours Service Interval: Every 100 hours/Yearly (whichever comes first)—Grease the bearings and bushings. Grease the machine more frequently when using it for heavy-duty operations. Grease specification: Mobilgrease XHP™-222 Removing the Hub and Rotor 1. Lift the front of the machine and support it with jack stands. 2. Remove the 4 lug nuts that secure the wheel to the hub (Figure 31). Grease Type: No.
g192347 Figure 34 1. Spindle 2. Hub and rotor assembly g033047 Figure 32 1. Flange-head bolts (3/8 x 3/4 inch) 3. Caliper bracket (brake assembly) 2. Spindle 4. Remove the dust cap from the hub (Figure 33). g192346 Figure 33 1. Cotter pin 4. Spindle nut 2. Spindle 5. Nut retainer 3. Tab washer 6. Dust cap 5. Remove the cotter pin and nut retainer from the spindle and spindle nut (Figure 33). 6.
Installing the Hub and Rotor Greasing the Wheel Bearings 1. 1. Remove the outboard bearing and bearing race from the hub (Figure 35). Apply a light coat of the specified grease to the spindle (Figure 36). g192344 Figure 36 g033050 Figure 35 1. Seal 4. Bearing cavity (hub) 2. Inboard bearing 5. Outboard-bearing race 3. Inboard-bearing race 6. Outboard bearing 2. Remove the seal, inboard bearing from the hub (Figure 35). 3. Wipe clean the seal and check for wear and damage. 1.
Electrical System Maintenance Electrical System Safety • Disconnect the battery before repairing the • g192345 Figure 37 1. Cotter pin 3. Dust cap 2. Nut retainer 9. Battery Safety Install the cotter pin and bend each legs around the retainer (Figure 37). 10. Install the dust cap onto the hub (Figure 37). 11. Repeat steps 1 through 10 for the hub and rotor at the other side of the machine. • To reduce the potential for fire, keep the batteries • • Installing the Brakes and Wheels 1.
• Electrolyte is poisonous. – Do not drink the electrolyte. – If electrolyte has been swallowed, have them drink large quantities of water immediately to dilute the electrolyte, if possible. – Do not attempt to make them vomit. – Call a poison control center and get medical attention immediately. • When not filling the batteries, keep the battery vent caps tight on the batteries. Do not operate the machine if any of the vent caps are missing or damaged.
Maintaining the Batteries Cleaning the Batteries Raise the seat assembly and raise the cargo bed before maintaining the batteries; refer to Raising and Lowering the Seat Assembly (page 29) and Raising the Cargo Bed to the Dump Position (page 19). Service Interval: Every 25 hours 1. Ensure that all the battery caps are tight. 2. Use a paper towel to clean the batteries. 3. If the battery terminals are corroded, clean them with a solution of 4 parts water and 1 part baking soda.
3. Connect a 16 gauge (or larger diameter), 2.5 m (8.2 ft) or shorter charger cord to the charging receptacle on the machine (Figure 38). Refer to the following table and Figure 38 for information on the meanings of the varying colors of the charger-status light. Note: Ensure that the charger-voltage setting matches the voltage at the power outlet being used.
Checking the Water Level of the Batteries key, and raise cargo bed; Raising the Cargo Bed to the Dump Position (page 19). Service Interval: Before each use or daily 1. Park the machine on a level surface, engage the parking brake, shut off the machine, remove the key, and raise cargo bed; Raising the Cargo Bed to the Dump Position (page 19). 2. Raise the seat assembly to access the batteries; refer to Raising and Lowering the Seat Assembly (page 29). 3.
Connecting the Batteries Disconnecting the Batteries 1. Raise the cargo bed, turn the key switch to the OFF position, and remove the key. 1. Ensure that the battery terminals are clean and free of oxidation. 2. Disconnect the main negative-battery cable (black) that connects the bank of batteries to the ground point of the machine (Figure 41). 2. Connect the main positive-battery cable (red) between the bank of batteries and the machine (Figure 41).
Replacing the Fuses There are 4 fuses in the electrical system; the other slots are open for options. They are located under the seat assembly behind a battery on the right side of the machine (Figure 42). Main power 10 A Electric relay 20 A 5 A USB power point Headlights 10 A Optional lift kit—open 15 A Horn 30 A g277621 Figure 43 1. Speed clip 4. Headlight 2. Opening in the bumper 5. Harness electrical connector 6. Lamp assembly 3. Adjustment screw 4.
Adjusting the Headlights Drive System Maintenance Use the following procedure to adjust the headlight beam position whenever a headlight assembly is replaced or removed. 1. 2. Maintaining the Tires Park the machine on a level surface with the headlights approximately 7.6 m (25 ft) from a wall (Figure 44). Service Interval: Every 100 hours—Check the condition of the tires and rims. Measure the distance from the floor to the center of the headlight and make a mark on the wall at the same height. 3.
Inspecting the Steering and Adjusting the Front Wheel Alignment Suspension Components Service Interval: Every 100 hours/Yearly (whichever comes first)—Check the front wheel camber and toe-in. Service Interval: Every 100 hours—Inspect the steering and suspension for loose or damaged components. With the steering wheel at the centered position (Figure 45), turn the steering wheel to the left or right.
Adjusting the Front Wheel Toe-in Checking the Transaxle-Fluid Level Important: Before adjusting toe-in, ensure that the camber adjustment is as close to neutral as possible; refer to Adjusting the Camber (page 41). 1. 2. Service Interval: Every 100 hours—Check the transaxle-fluid level. Ensure that the front tires are facing straight ahead. Measure the distance between both of the front tires at the axle height at both the front and rear of the front tires (Figure 48). 1.
Brake Maintenance Changing the Transaxle Fluid Checking the Parking Brake Service Interval: Every 100 hours—Check the transaxle for leaks. 1. Engage the parking brake by pulling the parking-brake lever toward you, until you feel tension. 2. If you do not feel tension when pulling the parking-brake toward you within 11.4 to 16.5 cm (4-1/2 to 6-1/2 inches) from the “P” symbol on the dash, then you need to adjust the parking brake; refer to Adjusting the Parking Brake (page 43).
8. Verify that the parking brake is adjusted to the proper tension; refer to Checking the Parking Brake (page 43). Note: If you cannot adjust the parking brake to the required tension, the brake pads may be worn and need to be replace. Contact your authorized Toro distributor for assistance. Checking the Brake-Fluid Level g002136 Figure 54 1. Brake-fluid reservoir Service Interval: Before each use or daily Check the brake-fluid level before the motor is first used. 4. Brake Fluid Type: DOT 3 1. 2.
Replacing the Service and Parking-Brake Pads Chassis Maintenance Adjusting the Cargo-Bed Latches Service Interval: Every 400 hours Contact your authorized Toro distributor to inspect and possibly replace the service and parking-brake pads. If the cargo-bed latch is out of adjustment, the cargo bed vibrates up and down as you drive the machine. You can adjust the latch posts to make the latches hold the cargo bed snugly to the chassis. Changing the Brake Fluid Service Interval: Every 1,000 hours 1.
Cleaning Washing the Machine Service Interval: Before each use or daily—Wash the machine. Wash the machine as needed using water alone or with a mild detergent. You may use a rag when washing the machine. Important: Do not use brackish or reclaimed water to clean the machine. Important: Pressurized water is not recommended when washing the machine. It may damage the electrical system, loosen important decals, or wash away necessary grease at friction points.
Storage 2. Important: If the machine cannot be plugged in during storage, fully charge the batteries at least once a month. The batteries self-discharge over long periods of time, which may damage the batteries to the point of being unusable, even if the batteries are new. Storage Safety • Shut off the machine, remove the key, and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Troubleshooting Machine-Status Light Flash Pattern Problem Possible Cause Corrective Action The machine-status light is always illuminated. 1. The system is functioning properly. 1. None The machine-status light flashed 1 time. 1. There is a controller-configuration fault. 1. Contact your Authorized Service Dealer. The machine-status light flashed 2 times. 1. The parking brake is engaged while in FORWARD or REVERSE position. 1. Disengage the parking brake. 2. A drive-switch fault occurred. 2.
Problem The machine-status light flashed 11 times. Possible Cause Corrective Action 1. A motor-encoder fault occurred. 1. Check the motor-encoder (speed sensor) wiring. 2. Exceeded the maximum motor speed. 2. Turn the key switch to the OFF position, wait a few seconds, turn the key switch to the ON position, and check for normal operation. The machine-status light flashed 12 times. 1. A controller-configuration fault occurred. 1. Contact your Authorized Service Dealer.
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
The Toro Warranty Electric Workman A Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. Where a warrantable condition exists, we will repair the Product at no cost to you including diagnostics, labor, parts, and transportation.