Installation Instructions

ManualsBrandsToro ManualsVehiclesBed Rack Kit, Workman GTX Series Utility Vehicles

FormNo.3406-387RevA

BedRackKit

Workman

GTXSeriesUtilityVehicles

ModelNo.07031

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

133-7204

1.Attention—readtheOperator’sManual;donotexceedload

weightsof18kg(40lbs).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-387*A

Summary of content (8 pages)

PAGE 1
Form No. 3406-387 Rev A Bed Rack Kit Workman® GTX Series Utility Vehicles Model No. 07031 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 133-7204 1.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 3
2. Install the 3 shovel mounts to the side upright frame brackets with 12 carriage bolts (5/16 x 3/4 inch) and 12 flange nuts (5/16 inch) as shown in Figure 2. 4. Install the pipe bracket to the 2 side upright frame brackets and front upright frame bracket with 6 carriage bolts (5/16 x 3/4 inch) and 6 flange nuts (5/16 inch) as shown in Figure 4. Figure 2 1. Carriage bolt (5/16 x 3/4 inch) 3. Flange nut (5/16 inch) 2. Side upright frame bracket 4. Shovel mount Figure 4 3.
PAGE 4
6. Install the front support bracket (with 1 hole on each side) to the 2 front upright frame brackets with 2 carriage bolts (5/16 x 3/4 inch) and 2 flange nuts (5/16 inch) as shown in Figure 6. 8. Install the fire-extinguisher mount to the side upright frame bracket and front upright frame bracket with 4 carriage bolts (5/16 x 3/4 inch) and 4 flange nuts (5/16 inch) as shown in Figure 8. Figure 8 Figure 6 1. Carriage bolt (5/16 x 3/4 inch) 3. Flange nut (5/16 inch) 2. Front upright frame bracket 4.
PAGE 5
9. Install the fire-extinguisher support or cup-cutter bracket to the side upright frame bracket and front upright frame bracket with 2 carriage bolts (5/16 x 3/4 inch) and 2 flange nuts (5/16 inch) as shown in Figure 9 or Figure 10. 10. Tighten the hex-head screws (1/4 x 3/4 inch) in steps 1 and 3 to 1,130 N∙cm (100 in-lb). Figure 9 1. Flange nut (5/16 inch) 4. Carriage bolt (5/16 x 3/4 inch) 2. Side upright frame bracket 5. Front upright frame bracket 3. Fire-extinguisher support Figure 10 1.
PAGE 6
When you complete installation, the Bed Rack Kit appears as follows: Left side installation—Figure 11 Both sides installation (additional parts required)—Figure 13 Figure 11 Right side installation (optional configuration)—Figure 12 Figure 13 Figure 12 6
PAGE 7
Notes: 7
PAGE 8