Installation Instructions

ManualsBrandsToro ManualsVehiclesTrash Can Mounting Kit, Workman GTX Series Utility Vehicle

FormNo.3404-868RevA

TrashCanMountingKit

Workman

GTXSeriesUtilityVehicle

ModelNo.07028

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocatednear

anyareaofpotentialdanger.Replaceany

decalthatisdamagedorlost.

133-4641

1.Warning—noridersontheattachment.

133-7138

1.Attention—readtheOperator'sManual;donotexceed22

kg(50lb)ofweightineachcontainer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3404-868*A

Summary of content (8 pages)

PAGE 1
Form No. 3404-868 Rev A Trash Can Mounting Kit Workman® GTX Series Utility Vehicle Model No. 07028 Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Trash-can frame Pivot-mount bracket Trash-can mount Hex-flange screw (3/8 x 2-1/2 inches) Shoulder screw (3/8 x 5/8 inch) Flange nut (3/8 inch) Clevis pin Hairpin cotter Outrigger (for machines with a plastic cargo bed only) 1 2 2 4 2 6 1 1 No parts required – Install the trash-can mounts (for machines with a steel cargo bed).
PAGE 3
Installing the Trash-Can Mounts to the Rear of the Machine 4. Install a pivot-mount bracket to a trash-can mount at the desired height using 2 hex-flange screws (3/8 x 2-1/2 inches) and 2 flange nuts (3/8 inch) as shown in Figure 4. Note: Repeat this procedure for the other assembly. For Machines with a Plastic Cargo Bed 1. Remove the 4 existing hex-flange screws (5/16 x 3/4 inch) from the bottom of the cargo bed (Figure 2). Important: Retain the 4 hex-flange screws (5/16 x 3/4 inch). Figure 2 1.
PAGE 4
6. Insert the trash-can frame into the machine receiver tube (Figure 6). 9. Insert the assembled trash-can mounts into the trash-can frame tubes (Figure 9). Important: Ensure that the slots for the outrigger posts are aligned as shown in Figure 6. Figure 9 2. Assembled trash-can mount 1. Trash-can frame tube Figure 6 1. Receiver tube 2. Trash-can frame 10.
PAGE 5
Installing the Trash-Can Mounts to the Rear of the Machine For Machines with a Steel Cargo Bed Repeat steps 4 through 10 of Installing the Trash-Can Mounts to the Rear of the Machine (page 3). Important: Do not install the outriggers.
PAGE 6
Installing the Trash-Can Mounts to the Front of the Machine For Machines With or Without the Brush Guard Kit Installed Repeat steps 4 through 10 of Installing the Trash-Can Mounts to the Rear of the Machine (page 3). Important: Do not install the outriggers.
PAGE 7
Without Brush Guard Kit Installation—Figure 13 Figure 13 7
PAGE 8