Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSlope Sensor Kit, LT3340 Triple Reel Mower or LT-F3000 Triple Flail Mower

FormNo.3440-871RevA

SlopeSensorKit

LT3340TripleReelMowerorLT-F3000TripleFlailMower

ModelNo.02951

InstallationInstructions

Note:ThiskitisforStage5machinesonly.

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal140-2710

140-2710

1.Warning—readtheOperator’sManual;afastashinglight

andalarmsoundingindicatesasteepslope;aslowashing

lightindicatesamoderateslope;nolightindicatesnormal

operatingconditions.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3440-871*

Summary of content (8 pages)

PAGE 1
Form No. 3440-871 Rev A Slope Sensor Kit LT3340 Triple Reel Mower or LT-F3000 Triple Flail Mower Model No. 02951 Installation Instructions Note: This kit is for Stage 5 machines only. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal140-2710 140-2710 1.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Prepare the machine. 2 Slope sensor Carriage bolt (1/4 x 2 inches) Lock nut (1/4 inch) Spacer Slope sensor decal 1 2 2 2 1 Install the kit. Fuse (2 A) 1 Install the fuse. No parts required – Calibrate the sensor.
PAGE 3
g308336 Figure 2 1. Machine-stability decal g338090 Figure 1 1. Carriage bolt (1/4 x 2 inches) 4. Slope snsor 2. Machine frame 5. Lock nut (1/4 inch) 3. Spacer 4. Locate the slope sensor connector in the main wire harness and plug it into the slope sensor. 5. Use cable ties to secure the wire harness away from moving parts or pinch points. 6. Install the slope-sensor decal adjacent to the machine-stability decal on the storage-pod lid (Figure 2). 3 2.
PAGE 4
3 Installing the Fuse Parts needed for this procedure: 1 Fuse (2 A) Procedure 1. Open the lid on the left pod. 2. Remove the 3 knobs inside the storage pod (Figure 3). g338477 Figure 4 1. Install the fuse in this location 5. 2. Fuse block Install the fuse-block cover and install the storage pod with the 3 knobs. 4 Calibrating the Sensor g338478 Figure 3 1. Knobs No Parts Required 2. Front knob 3. Remove the storage pod and locate the fuse block. 4.
PAGE 5
g317524 Figure 6 1. LED light 5. When the InfoCenter shows Message 601, Slope Sensor Calibrated, Cycle keyswitch, and the light no longer blinks, turn the ignition key to the OFF position. 6. Disconnect the calibration connectors and install the plug onto the connectors. g350905 Figure 5 1. Calibration connectors 2. Plug g315597 3. Turn the ignition key to the ON position, but do not start the engine. 4. The InfoCenter shows Message 600, Slope Sensor Calibrating. Figure 7 1.
PAGE 6
Operation Using the Slope Sensor The light and alarm indicates the severity of the slope: • Red light—normal operating conditions • Slow, flashing red light and Advisory B2713 displaying on the screen—moderate slope g317557 Figure 8 Advisory B2713 • Fast, flashing red light, audible alarm, and Advisory B2714 displaying on the screen—steep slope; proceed to a more shallow slope.
PAGE 7
Notes:
PAGE 8