Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSlope Sensor Kit, T4240, CT2240, or LT3340 Turf Mower Traction Unit

FormNo.3437-895RevA

SlopeSensorKit

ModelNo.02945

ModelNo.02946

ModelNo.02947

ModelNo.02949

ModelNo.02950

InstallationInstructions

Refertothefollowingtablefortheappropriate

kit,tractionunit,andtraction-unitserialnumber

combination:

KitModel

Number

TractionUnitModel

Number

SerialNumber

02750(T4240)

405398421andabove

30654(CT2240)

405623665andabove

31654(CT2240)

Allserialnumbers

02945

30657(LT3340—cab

equipped)

405006390andabove

30657(LT3340)

405006390andabove

02946

30659(LT-F3000)

404879018andabove

02947

30659

(LT-F3000—cab

equipped)

404879018andabove

02949

02750(T4240—cab

equipped)

405398421andabove

02950

31050TE(PLH800)

320000155andabove

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal140-2710

140-2710

1.1.Warning—readtheOperator’sManual;afastashing

lightandalarmsoundingindicatesasteepslope;aslow

ashinglightindicatesamoderateslope;nolightindicates

normaloperatingconditions.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3437-895*A

Summary of content (8 pages)

PAGE 1
Form No. 3437-895 Rev A Slope Sensor Kit Model No. 02945 Model No. 02946 Model No. 02947 Model No. 02949 Model No.
PAGE 2
Installation 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Lower the cutting unit(s). 4. Shut off the machine and remove the key.
PAGE 3
g307377 g305020 Figure 5 Figure 3 1. Bolt (M10) 1. LED light 3. Flange nut (M10) 2. Slope sensor mount 8. 4. Install the wire harness connector labeled P02 to the slope sensor (Figure 4). Connect the remaining wire-harness connectors as follows: • Wire harness connector labeled P01: Connect to one of the 6-pin sealed connectors located on the main harness below the control panel. • Wire harness connector labeled P08: Connect to the LED light.
PAGE 4
6. Connect the LED light to the wire-harness connector labeled P08 (Figure 8). g308240 Figure 6 1. Slope-sensor decal g304404 Figure 8 Installing the Kit CT2240, LT3340, and LTF Machines 1. Remove the 6 screws securing the control panel to the control pod (Figure 7). g304897 Figure 7 1. Screw 3. Plug 2. Control panel 4. Control pod 2. Carefully lift off the panel, ensuring that the connectors to the existing switches are not disturbed. 3. Remove the plug (Figure 7) from the console. 4.
PAGE 5
17. Install the slope-sensor decal adjacent to the machine-stability decal on the storage-pod lid (Figure 11). g304544 Figure 9 1. Bolt (M6 x 35 mm) 3. Slope sensor 2. Slope sensor mount 4. Flange nut (M6) g308336 Figure 11 13. Connect the wire-harness connector labeled P02 to the slope sensor. 14. Use 2 bolts (M6 x 25 mm) and 2 flange nuts (M6) to secure the slope sensor mount to the electrical panel (Figure 10). 1. Machine-stability decal 2.
PAGE 6
3. Remove the steering wheel, dashboard, and front panel (Figure 13). Note: Carefully lift off the dashboard, ensuring that the connectors to the existing switches are not disturbed. g307287 Figure 14 1. LED light 2. Slope sensor decal g307374 Figure 13 1. Front panel 3. Steering wheel 2. Dashboard 4. Remove the plug and install the LED light and the slope-sensor decal to the dashboard (Figure 14). If a hole for the LED light is not present, drill a 19-mm hole in the location shown in Figure 15..
PAGE 7
g307376 Figure 18 g307375 Figure 16 1. Wire-harness-routing direction 1. Alarm 8. Connect the remaining wire-harness connectors as follows: • Wire harness connector labeled P08: Connect to the LED light. • Wire harness connector labeled P09: Connect to the alarm. 9. Use a cable tie to coil together any additional amount of wire harness in front of the battery (Figure 19). g308238 Figure 17 1. 30 mm 6. 2.
PAGE 8
3 Calibrating the Sensor No Parts Required Procedure 1. While the machine is on a flat surface, remove the plug from calibration connectors (labeled P05 and P06). 2. Plug the connectors together. 3. Turn the ignition key to the ON position, but do not start the engine. Note: The LED light blinks as the sensor calibrates. 4. When the light no longer blinks, turn the ignition key to the OFF position. 5. Disconnect the calibration connectors and install the plug onto the connectors.