Installation Instructions

ManualsBrandsToro ManualsRiding ProductsFlashing Beacon Kit, LT-F3000 Heavy-Duty Triple Turf Flail Mower

FormNo.3410-585RevA

FlashingBeaconKit

CT,LT,andLT-FSeriesTripleTurfMowerorGroundsmaster

3400TractionUnit

ModelNo.02920—SerialNo.400000000andUp

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Important:Donotinstalltheashingbeaconkitonmachineswithacab.

PreparingtoInstallthe

FlashingBeaconKit

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.Lowerthemowerdeck,reelcuttingunit,orailcutting

unittotheground.

3.Engagetheparkingbrake.

4.Shutofftheengineremovethekey.

5.Waitforallmovingpartstostop.

OpeningtheHood

1.Insertthehoodkeyintothelockforthehoodand

rotatethelock90°counterclockwise(Figure1orFigure

2).

2.Releasethehoodlatches.

•Formachineswithatopmountedhoodlatch:

pressthebuttonofthehoodlatch(Figure1).

g189331

Figure1

•Formachineswithasidemountedhood

latches:removethe2hoodlatchesfromthelatch

catches(Figure2).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3410-585*A

Summary of content (12 pages)

PAGE 1
Form No. 3410-585 Rev A Flashing Beacon Kit CT, LT, and LT-F Series Triple Turf Mower or Groundsmaster® 3400 Traction Unit Model No. 02920—Serial No. 400000000 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Important: Do not install the flashing beacon kit on machines with a cab.
PAGE 2
g036762 Figure 2 g036763 3. Carefully rotate the hood back and down (Figure 4). Figure 4 Machines with a Side Mounted Hood Latches Disconnecting the Battery WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
PAGE 3
Removing the Bulkhead Panel WARNING 1. Remove the 4 bolts (6 x 25 mm), 4 lock washers (6 mm), and 4 flat washers (6 mm) that secure the bulkhead panel to the chassis of the machine (Figure 6). Incorrect battery cable routing could damage the machine and cables, causing sparks. Sparks can cause the battery gases to explode, resulting in personal injury. • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable.
PAGE 4
the brackets with the 2 small bolts, 4 small washers, and 2 small locknuts. g035796 Figure 7 1. Bolt (discard) 3. Washer (retain) 2. Lanyard washer 4. Locknut (discard) 3. Align the hole in the ROPS bracket with the hole in the ROPS and install the new bolt with the existing washer (Figure 8). g036075 Figure 9 1. Beacon bracket 3. Small washer (4) 2. Small bolt (2) 4. Small locknut (2) Installing the Beacon 1. Install the beacon stand to the beacon bracket (Figure 10).
PAGE 5
g036076 Figure 10 1. Beacon stand 2. Seal 3. Nut 4. Beacon cable 2. To fit the beacon cable, start by removing the fitting in the top of the beacon stand and feed the beacon cable through the bottom and out through the top. g036077 Figure 12 3. Connect the beacon cable, ensuring that the red connector is fitted to the central positive terminal of the beacon stand fitting, and the black connector to the outer terminal. Screw the fitting back into the beacon stand. 6.
PAGE 6
Completing the Installation Installing the Bulkhead Panel 1. Align the 4 holes in the bulkhead panel with the 4 clip nuts on the chassis; refer to Figure 6 in Removing the Bulkhead Panel (page 3). 2. Secure the bulkhead panel to the chassis of the machine with the 4 bolts, 4 lock washers, and 4 flat washers; refer to Figure 6 in Removing the Bulkhead Panel (page 3). g035802 Figure 14 3. Torque the bolts to 7.7 to 11.6 N∙m (68 to 103 in-lb). 1.
PAGE 7
Operation Using the Beacon To turn on the beacon, press the bottom of the switch. To shut off the beacon, press the top of the switch. Note: The ignition switch must be in position 1 for the beacon to work. g188128 Figure 17 Maintenance 1. 10 A fuse 2. Fuse block socket (3rd position from the right) Replacing the Fuse 3. Insert a 10 A fuse into the slot of the fuse block located at the 3rd position from the right (Figure 17). 1. Remove the cover from the fuse block (Figure 16).
PAGE 8
Notes:
PAGE 9
Notes:
PAGE 10
Notes:
PAGE 11
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
PAGE 12
The Toro Warranty A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).