USER MANUAL TOrigin TIP
Content Safety Instructions 3 Appearance 4 Connection Guide 5 Instructions RCU 6-7 Initial Setup 8-9 Main Menu Troubleshooting 10 11-12 2
Safety Instructions Removing the cover of the receiver may lead to a severe and potentially fatal electric shock. This digital receiver has been manufactured to meet international safety standards. However, safety precautions must be followed to ensure the safe and reliable operation of the device. Please take note of the following guidelines to avoid the risk of an electric shock. • This device operates with an external power supply in the range of 100 to 240V AC, 50/60 Hz.
Appearance Front panel: 1 – Infrared Receiver 1 2 3 4 2 – Sleep Indicator 3 – Router Indicator 4 – Power Indicator Side panel: Rear panel: 1 2 3 4 5 6 7 8 1 – Input/Output RF (WiFi Signal) 6 – RESET 2 – DC IN (DC12V 0.
Connection Guide Cabl e HDM I Adaptor RCA Cabl e Step 1: Connect the antenna, providing the antenna, to the “RF IN” on the back of TOrigin TIP Step 2: Connect the TOrigin TIP and your TV by using the RCA or HDMI cable (supplied with TOrigin TIP), connected to the AV OUT or HDMI connector on the back of the TOrigin TIP. Step 3: Connect to TOrigin TIP to Router Use Network cable Step 4: Connect the supplied power adaptor to the “DC IN” on TOrigin TIP and plug the adaptor in the wall socket.
Instructions RCU 1 2 8. 9. 3 4 10. 6 5 7 9 11. 8 10 11 12. 12 14 13 13. 14. 15 16 17 20 21 19 18 23 22 25 26 27 24 28 29 15. 16. 17. 18. 19. 1. 2. 3. 4. 5. 6. 7. 6 POWER - puts STB into standby mode. To switch off STB please disconnect the adapter from power supply. MUTE - Mutes and unmutes TV volume. Digital buttons (0 ...
Instructions RCU How to use the learning function in the control remote Step 1: Press and hold the the 29 ( ) button for 3 seconds until the red LED indicator lights continuously, at which time the set-top box remote control enters the learning mode. indicator TV Volume Channel TV Step 2: After a few seconds, press the button for the “TV” area you want to learn. The remote control will go into standby mode, waiting for a signal to be received to learn.
Initial Setup When you turn on the receiver for the time, you need to select the menu language, the time zone, TV picture format, and antenna power. Image format: Use this option to select the aspect ratio at TV. Antenna power: Set to On if you are using an active one antenna. When set to “On”, on the ANT IN jack of the receiver will be 5V. Use "Off" for passive antennas (antennas that have self-powered) or when you are connected to a home distribution system.
Initial Setup After search completed, you will see a list of the found channels. Using ▲ and ▼, select a channel and press , to start watching the program. How to set up channels after the initial setup Step 1: Press the MENU button on the RCU. Using ◄ and ► buttons select "Search". In this menu, select Auto or Manual Search. Step 2: Auto search will set scanning of all frequencies and modulations. Manual search requires the introduction of data of Frequency, Symbol rate and QAM.
Main Menu To enter the main menu press the MENU button on the RCU. You can navigate through menus using ▲ and ▼ on the RCU, press item. to enter the selected Attention! Some menu options require input a parental password. The default password is «0000».
Troubleshooting There can be many reasons why your receiver does not work properly. If the receiver does not work as expected, check the instructions below. If the receiver still does not work properly after checking, contact your service provider. Do not open the receiver cover. Opening will void the warranty and repairs within the warranty period will be denied.
Troubleshooting Problem The receiver cannot be operated with the remote control Potential Reasons What to do The batteries are empty / incorrectly inserted. The receiver is unplugged or turned off. Replace the batteries / check that the poles are installed correctly. Connect the receiver to the mains / switch it on. The remote control is not pointed correctly. The infrared sensor is shielded. Point the remote at the front panel receiver. Check for obstacles or other possible impacts.
TOrigin TIP