2.
INTRODUCTION Thank you for purchasing our product, please read it thoroughly before operating and keep it for future reference. The Digital Wireless Rear Vision System will improve your ability to see behind your car, pickup truck, camper, travel trailer, fifth wheel trailer or motorhome. We have taken numerous measures to ensure that your product is delivered in top condition and will perform to your satisfaction.
.Accessories Suction cup mount Remote Control Power Cord Antenna Detachable Sunshield Screws & Bolt User Manual clamps Power Adapter for Furrion Pre-Wired RV Attention: The above accessories list may have little differences for different retail platforms, we may increase or update some accessories without notifying in advance, please subject to the actual received package. 4. Monitor Power Cable These instructions do not apply to all vehicles.
Allen Screw 4x8 Washer ¢5 Camera Positioning Camera location Wiring Installation The system can be used as a rear observation system or as a backup camera system. ·To use as a rear observation system, the camera needs to be wired to a constant 12V/24V power source. Ex: If connected to running lights or marker lights, the lights must be ON for the system to operate. ·To use system as a backup camera system, the camera needs to be wired to a circuit that turns on when the reverse gear in engaged.
2.Before drilling the hole,make sure there are no components behind the surface you are drilling such as electrical cables,gas lines,or other important components that can be damaged. 3.After drilling the hole,insert the supplied grommet then route the camera cable into the opening. The grommet must be used to prevent the metal edge from cutting the cable. 4.Locate the power source required:Backup lights if used as a backup camera or running/marker lights is used as a rear observation system. 5.
e.adjust the knob to set the screen at a good viewing angle and tighten knob on the bracket to lock into position. To maximize the efficiency of the suction cup mount, it is recommended that the mounting be performed under the following conditions: ·Surface temperature should be between 21°C and 38°C. ·Mounting below 10°C should be avoided. ·Mounting should not occur in direct sunlight. Mounting should be protected from direct sunlight exposure for a period of 24 hours. 2.
1. When the green wire is activated, the monitor automatically switches to CAM1. 2. When the blue wire is connected to the positive wire of the left turn light, the monitor automatically switches to CAM2(left side camera) when the left turn indicator is activated. 3. When the brown wire is connected to the positive wire of the right turn light, the monitor automatically switches to CAM3 (right side camera) when the right turn indicator is activated. 4.
3. Pairing Press the “M” button to enter in main menu and press “REC” key to enter pairing interface. Press “ REC ” key to enter pairing state when PAIRING START appears. CAM2 PAIRING START 20 At this time, press the button on the camera to pair the camera with the monitor.
4. Setup Press the “-”or “+” button to select SETUP on the screen 4.1 PICTURE PICTURE: Press the “REC ”key to enter BRIGHTNESS,CONTRAST,HUE and VOLUME settings. (1) BRIGHTNESS setting Select the Brightness icon,press“REC ”key to enter settings,press “-”or“+” keys to select the required Brightness setting. (2) CONTRAST setting Select the Contrast icon, press“REC ”key to enter settings,press “-”or “+” keys to select the required Contrast setting.
4.3 MODE MODE : Press “CAM” to switch image as below. 4.4 CAM-SETUP Press “-”or “+”to select CAM SETUP,press “REC” to enter. AUTO SCAN mode enable it can loop display each channel at 5-45 seconds, you can turn off any channels when no need or turn on or off the auto scan mode freely. 4.
4.6 PLAY Press “-”or “+”to select the recorded video clips, press “REC” to playback. 4.7 RECORD Press “-”or “+”to select RECORD, press “REC” to enter. REWRITE: When SD card is full,the monitor will delete the earliest recorded file one by one,and keep recording. FORMAT: SD card must be formatted before being used. All documents in SD card will be lost once format the card. 5. Camera Transmitter operation 5.
5.2 The paired camera transmitter can trigger the receiver to work automatically after power is on. The screen display delay is less than one second. 5.3 The camera transmitter has infrared night view function. If it is too dark, the infrared LED is automatically turned on for supplemental lighting. CAUTION: The LED will emit faint red light when turned ON. Do not stare at the light for a long period. This could cause eye injuries.
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.