eTag® Board Hardware User Manual Version 2.
eTag® Board: User Manual Table of Contents Manual .......................................................................................................................................................... 3 Disclaimer...................................................................................................................................................... 3 Contact Information..........................................................................................................................
eTag® Board: User Manual Manual Safety Guidelines Warning notices must be observed to ensure personnel safety as well as that of others, and to protect the product and connected equipment or process. These warning notices are accompanied by a clarification of the level of caution to be observed. Qualified Personnel This device/system may only be set up and operated in conjunction with this manual.
eTag® Board: User Manual Innovation, Science and Economic Development Canada This device contains licence‐exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence‐exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
eTag® Board: User Manual eTag® Board Introduction The eTag® Board system will discover tagged assets placed on these boards – providing location data for tags in strategically identified zones. They provide a mechanism for centrally viewing the location of personnel in real time. Using a passive tag reader interface, the eTag® Boards will locate the tag on the boards and identify which zone or region the tag was placed.
eTag® Board: User Manual Components of eTag® System eTag® Board 2x2 eTag® Board 1x2 14.5’’ x 25.375’’ x 2’’ (HxWxD) 27’’ x 24.5’’ x 2’’ (HxWxD) eTag® Controller Box 11.024’’ x 11.024’’ x 5.
eTag® Board: User Manual Cables eTag® Board Coaxial SMA Male-Male cables come in 5 standard lengths. 05ft, 10ft, 15ft, 20ft, 25ft. Custom lengths are available.
eTag® Board: User Manual eTag® Board Mounting The eTag® Board is mounted using the 2 mounting holes inside the cableway as well as the 2 mounting holes on the opposite side of the board. 1. Open the cableway to be able to access the mounting holes. 2. With proper bolts for mounting area, secure the eTag® Board to the wall. 3. Secure the eTag® board with the mounting holes on the opposite side of the cable way. Installation 1) Setting the eTag® Board controllers IP address.
eTag® Board: User Manual 2) Physical Installation. a) Install the eTag® Controller enclosure (in range of the cables used to connect the eTag® Boards) using the mounting holes or bracket. b) Attach the male SMA coax cables to the eTag® Board antenna connectors. Note: Although the eTag® Board is factory calibrated, it may require fine tuning once installed to optimize performance. Nearby Ferro magnetic materials can affect the antenna negatively.
eTag® Board: User Manual Specifications eTag® Board Dimensions 1x2 2x2 Height 14.5” 27” Width 25.375” 24.5” Depth 2” 2” Tags (Max) 36 50 eTag® Board 1x2. eTag® Board 2x2.
eTag® Board: User Manual eTag® Controller Dimensions Enclosure Height 12” Width 10” Depth 5” 11
eTag® Board: User Manual Power Consumption Input Voltage 120VAC 1A Power Consumption MAX 16VA Operating Frequencies eTag® Board 13.56Mhz 1W-5W (adjustable) Data Transmission Networking Ethernet RJ45 (TCP/IP) Environmental Temperature Range Operation -25°C to 55°C Storage -25°C to 85°C Relative Humidity 5% to 80% (Non-Condensing) Connections eTag® Board Female SMA connectors optionally located at the Top; Bottom; Left; Right.
eTag® Board: User Manual Part Numbers eTag® Board Part Number. ET - ___ ___ 1 2 Example: - ___ _0_ _0_ - 3 ___ 4 ET-22-T00-0 Sections are 2ft x 2ft. Antenna connector port on the Top of the board. 0 No additional requirements. 1. Section Height. (Options for eTag® dimensions 1ft or 2ft) 2. Section Width. (Options for eTag® dimensions 1ft or 2ft) 3. Position of the antenna connector. T = Top; B = Bottom; L = Left; R = Right. 4. Additional Info. 0 = No additional information.
eTag® Board: User Manual eTag® Board Control Box Part Number. ET-JB - ___ - ___ 2 1 Example: ET-CB-8-0 eTag® Board with 8 sections Antennas. 0 No additional requirements. 1. Total Number of sections. (Options 1-8) This will allow to know if using 1, 4 or 8 channel. 1 = Single channel 4 = 4 channel 8 = 8 channel 2. 0 = No additional information. C = Custom specifications, must describe requirements. eTag® Board Antenna Cables Part Number.