AR1021X-NV5 Specification Customer: Description: AR1021X-NV5 Customer P/N: Date: Customer Approve Auditing Ad mit Auditing Ad mit Provider Approve
Product Specification 802.11a /n USB AR1021X-Module AR1021X-NV5 Version 1.0 Docume nt release Version 1.
CONTENTS 1. Product Overview............................................................................................................................ 2. Module Hardware Overview........................................................................................................... 2.1 Block Diagram...................................................................................................................... 2.2 2.3 Features.......................................................................
1. Product Overview The module AR1021XNV5 provides wireless modem functionality for CE applications utilizing direct sequence spread spectrum and OFDM/CCK technology. The module supports IEEE 802.11a/n protocol. Data rate of up to 54Mbps for 802.11a and 144.4Mbps for 802.11n HT20,300Mbps for HT40.The module integrates all wifi functionality in a package friendly to lowcost PCB design, requiring only a external 3.3V power supply and connection to antenna.
2.2 Features IEEE802.11a/n (2X2) based on Qualcomm Atheros AR1021X solution USB 2.0 Interface, High and Full Speeds supported Module is powered by the host with a 3.3V +/- 10% supply. Internal OTP memory for calibration data Advanced power management to minimize standby,sleep and active power Security support for WPS,WPA2,WPA,WAP and protected management frames Full 802.11e QoS support including WMM and U-APSD Support for the IEEE 802.
2.3 Interface Interface • Interface: Half Hole • Antenna: IPEX connector Pin definition From Module TOP View Pin Symbol Name Sta tus Pin Description Num ber 1 LED O LED indication 2 GND P Ground pad 3 USB_DP I/O USB D+ signal 4 USB_DN I/O USB D- signal 5 3.3V P Analog 3.
3. Electrical Specification 3.1 Recommended operating rating Element Sym bol DC supply voltage UV+ M i n 3. 0 T y p 3 . 3 M a x 3. 6 U ni t ( V ) 3.2 DC Characteristics Sy mb Parame ter Min Typ M a x Un it Supply voltage 3.0 3.3 Power Saving -- 450 3. 6 -- Standby -- 112 -- Continuous Tx Current 5GHz(Dual Chain) -- 480 -- Continuous Rx Current 5GHz(Dual Chain) -- 60 -- (V ) (u A) (m A) (m A) (m A) ol ST B Y 3. 3V 3.
4. RF Specification 4.1 IEEE 802.11a Items Specification Modulation technique Channel Data rate TX Characteristics 1. Power Levels(SISO) 1)Target Power@6Mbps 2)Target Power@9Mbps 3)Target Power@12Mbps 4)Target Power@18Mbps 5)Target Power@24Mbps 6)Target Power@36Mbps 7)Target Power@48Mbps 8)Target Power@54Mbps 2. Spectrum Mask@Target Power 1) at fc ± 11MHz 2) at fc ± 20MHz 3) at fc > ± 30MHz 3. Frequence Error 4.
4.2 IEEE 802.11n HT20(5G) Item s Specification Modulation technique Channel Data rate TX Characteristics 1. Power Levels 1)Target Power@MCS0 2)Target Power@MCS1 3)Target Power@MCS2 4)Target Power@MCS3 5)Target Power@MCS4 6)Target Power@MCS5 7)Target Power@MCS6 8)Target Power@MCS7 2. Spectrum Mask@14dBm 1) at fc ± 11MHz Contents Mi n.
4.3 IEEE 802.11n HT40(5G) Item s Specification Modulation technique Channel Data rate TX Characteristics 1. Power Levels 1)Target Power@MCS0 2)Target Power@MCS1 3)Target Power@MCS2 4)Target Power@MCS3 5)Target Power@MCS4 6)Target Power@MCS5 7)Target Power@MCS6 8)Target Power@MCS7 2. Spectrum Mask@14dBm 1) at fc ± 11MHz 2) at fc ± 20MHz 3) at fc > ± 30MHz 3. Frequence Error 4. Modulation Accuracy(EVM)@Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 RX Characteristics 5.
5.Mechanical Specifications PCB Assembly Dimension: Dimension (L x W x H): L:19.0mm* W:27.0mm * H:2.3 mm Solder joints used by the module is connected to the terminal device.
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
