Quick Start Guide Product introduction MDT740 has optional features (wifi, BT, GPS, 2G/3G/4G,LoRa, back camera, front camera, RFID, lightsensor, gyroscope, accelerometer) Highlights: 4G – pls insert the SIM card when the device if complete off front camera – there are 6 IR LED around the camera. if you enable the flash function in front camera, then you will see the IR LED is on.
Direction of SIM card and SD card All rights reserved.
Interface 1. There is TTL serial port (Tx/RX) or OTG from 10 pin usb connector 10pin usb connector pls see the above schematics of our USB connector in our PND, it is 10 pin connector. Pin 4 and 6 can be used for USB or TTL serial interface (Rx/Tx) and Pin 8 is ID pin which is used to distinguish for USB or serial interface. if it is connected to GND, then the pin 4 and 6 will be Rx/Tx interface. if it is connected to Vcc, then the pin 4 and 6 will be D- and D+. All rights reserved.
2. There are Rs232 interface and OTG from cradle. Highlights: OTG port from device (10pin usb connector) and cradle are sharing same pins. Only 1 OTG interface can be used. Usb connector for OTG or charging This cable can be customized when you placed order For sample, it will be 12 pins connector, pls see below or pins assignment Pin 1 – Ignition (Green), it can be wake up the device. see the software section for more details.
Removing the cradle cable (12pin molex connector) if you don’t want to use it. 1. you can find the rubber plug in our blackbox (see below picture). 2. open the cradle casing by screw driver 3. remove the 12pin molex cable from connector 4. put the rubber plug in the hole and close the cradle casing Option for ignition control the power supply If ignition is OFF, the power supply will cut. Customer uses their application to control the device to power off or sleep mode.
Device installation There are few options 1. Directly attach mount to device (no cradle in this case) 2 screw hole at the back Pls use M4 15mm screw if the mount thickness is 9mm. Pls note that the screw hole depth is only 6mm. Long screw may damge the PCB inside 2.
Mount options: There are many car mount options. You can use the 2 screw hole (black colour) or 4 screw hole (yellow colour) to attach the different mount system. The 4 screw hole depth is 5mm long only, pls prepare correct screw. Pls note that wrong screw length may damage the cradle. Option 1: Low cost wind shield car mount Option 2: Many mount option from RAM MOUNT You can choose the mount you like from their website (www.rammount.com) Example 1 (RAP-B-166-2U) All rights reserved.
Example 2 (RAM-B-138-224-1U) Example 3 (RAM-B-138U-A) Example 4 (RAP-B-138-AU) All rights reserved.
Option 3: You can also choose mount from HR (http://www.hr-autocomfort.de/) There are 4 hole plate which you can lock in the cradle with 4 screw hole. then, you can choose the mount from HR. Example 1 (1719/0) Option 4: Mounting solution from truck expert (ARAT) http://www.arat-de.eu/index.php?ber_id=10&dia_id=1&lang=en All rights reserved.
Option 5: There are other mount which can support this 2 screw hole and 4 screw hole at the back can be used. For my understanding, there are other mount company also use this 2 or 4 screw hole as standard. Pls let know if you need other mounting system or solution. All rights reserved.
New silicon sleeve It can have more protection for the device. 1. It also support stylus. There are optional clip which you can install at the back of the sleeve. 2. There is new cradle (dock) to match the device with sleeve. This cradle can be used for the device with or without the sleeve. All rights reserved.
Software support We can provide serial port apk and NFC demo. Pls contact our Sales for details. 1. Pls also see the software setting for serial port two serial ports are available on the device : one shares the the USB data pins of the mini A/B USB connector. Only TX and RX pins are available, voltage is TTL 3.3V. one is on the Pogopin interface (pins 3, 5, 6 and 7). TX, RX CTS and RTS are available, voltage is RS232.
Video input cradle We made a new video input cradle 1. For rear view camera input, we have complete demo kit (part number: CRD741R) Highlights for P2 connector: 1. It is same as before. We just add video trigger (pin 12), this video trigger can support only 9-32V 2. The ignition status cannot read by device anymore. It is used only to control the power supply from the device. If ignition is ON, the device can be charged. If ignition is OFF, the device cannot be charged.
Scanner You can using scanner to our device 1. Plug the special USB cable with marked “scanner” to the mini_USB port on the back of the scanner.. 2. Plug the other end of the special USB cable with marked “MDT” to the Device or the Cradle All rights reserved.
3. Turn on the scanner 4. Inserted a USB flash drive or a memory card in the scanner. 5. When scanning is finished, the image is saved on the memory card or USB flash drive. Will show in the ES File Explorer in the Device 6. You can charge the scanner battery by plug the special USB cable on the Device. All rights reserved.
CE Caution: Use the Product in the environment with the temperature Between -10℃ and 40℃; Otherwise, it may damage your product. For the following equipment: Product Name: GPS Model: MDT740, MDT741, MDT742, MDT752, MDT714D, OBC740, M710A, M710AG, M710AB, M710AKB, M740B, MDT840, MDT841, MDT814D Brand Name: / TOPICON HK LIMITED E-mail: keller.sin@topicon.
Support Networks: GSM, GPRS, EDGE RF Output Power: GSM900: 32.52dBm, GSM1800: 29.98dBm EDGE900: 26.74dBm, EDGE1800: 27.85dBm Support Networks: WCDMA, HSDPA, HSUPA RF Output Power: WCDMA Band 1: 23.37dBm, WCDMA Band 8: 22.49dBm Support Bands: FDD-LTE Band1, 3, 7, 8, 20 FDD-LTE Band 1: 23.51dBm, FDD-LTE Band 3: 23.92dBm, FDD-LTE Band 7: 22.84dBm, FDD-LTE Band 8: 22.89dBm, FDD-LTE Band 20: 23.29dBm Bluetooth Version: Bluetooth V4.0 Max.RF Output Power: 5.32dBm (EIRP) Frequency Range: 2412-2472MHz for 802.
FCC RF Exposure Information and Statement This device meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. The SAR limit of USA (FCC) is 1.6 W/kg averaged.