TOPFLYtech SolarGuardX 100 GPS E-Lock User Manual 20220329
Thanks for your purchasing of the high-quality GPS tracker from TOPFLYtech. Please read this user manual carefully before installation and operation. Information in this manual is the property of TOPFLYtech. Changes to the specifications and features in this manual may be made by TOPFLYtech without prior notice. No part of this manual could be reproduced, copied, translated, transmitted, or published in any form or by any means without TOPFLYtech's prior written permission.
Contents 1. QUICK REFERENCE ..............................................................................................................................4 2. PRODUCT SPECIFICATIONS ..............................................................................................................5 3. STANDARD ACCESSORIES INTRODUCTION ................................................................................7 4. LED INDICATOR ...........................................................................
1. Quick Reference SolarGuardX 100 Attention i. SolarGuardX 100 obtains power through sunlight to extend the battery life. ii. Please make sure that the device is exposed to direct sunlight every day. This will be very useful to extend the battery life. If the device is not charged for more than three months, it may cause permanent damage to the internal battery. iii. Please give the device a fully charging before installation. iv. Only when the solar panel output voltage value is 0.
ii. The typical charging rate of the solar panel under direct sunlight at noon (in summer) is about 330mAh (different sunlight illumination, different charging current). Disclaimer: Before using this device, customers should fully understand their usage scenarios and installation environment. TOPFLYtech will not be responsible for any lost caused by using the device in a wrong scenario or reporting rate. It is highly recommended that customers should contact TOPFLYtech before deployment.
GNSS Chipset MediaTek High Gain GNSS receiver GNSS System GPS+Glonass or GPS+Beidou Receiver type: 33 tracking / 99 acquisitions- channel GNSS receiver Sensitivity Cold start: -149 dBm Tracking: -167 dBm Horizontal Position Accuracy < 2.
3. Standard Accessories Introduction 4. LED indicator Note: Indicator lights will go out automatically after the tracker turns on for 70 seconds without connecting to the external power via USB cable. LED indicator working status: Solid on: LED indicator on and no flashing Fast flashing: 0.25 second on and 0.25 second off Slow flashing: 1 second on and 1 second off Unlock: Unlock successfully, RFID LED indicator will show solid on until plug out the lock rope. If Shenzhen TOPFLYtech Co., Limited.
the rope isn’t taken out in 60 seconds, device will lock again, and LED indicator goes off. Lock: After lock successfully, RFID LED indicator will be fast flashing for 2 seconds then off. Wake up the device: Device gets the wake up info, RFID LED indicator will show slow flashing 300 seconds or get the unlock command from server side then switch to unlock process. Incorrect RFID Card or Correct RFID Communication Error: Network & GNSS & RFID LED Fast flashing 5 seconds.
5.3.1 It is VERY IMPORTANT to fix the 4 SIM card cover screws to prevent water from leaking inside and cause damage to device. 5.3.2 TOPFLYtech offers the electric screwdriver (TA38) as an optional accessory to help customer standardize the screw fixing strength. 5.3.3 Please use strength level 8 if using TOPFLYtech electric screwdriver (TA38) 5.3.4 For third party electric screwdriver, please use torque 3.5kgf.cm. 5.4 Installation 5.4.
6.3.2 Platform Query Connect your tracker to the tracking platform then check the real-time position online. (Additional tracking service charge may happen. Contact with your service provider to get more details) 7. Alarm Configuration Alarm configuration please via the TOPFLYtech configuration tool. 8. Quick Trouble Shooting 8.1 Unable to Connect to the Tracking Platform 8.1.1 Check the APN and IP settings. 8.1.2 Check the SIM card data service whether enabled. 8.1.
by comma and ends with #. When set successfully, the tracker will return OK and execute it. Otherwise, there will be no message returned.
Note: 1) Tracker will return “SET APN OK” when received this command. 2) If there is no Username and Password, the SMS setting is: APN,Current PIN,APN Name,,# 3) If there is no APN PIN, the SMS setting is: APN,Current PIN,APN Name,Username,# 10.
Heartbeat Interval: Range: Positive Integer Range Limit: 1 ~ 255 minutes Default: 30 minutes Note: Tracker will return “SET HBT OK” when received this command. 10.6 PIN Setting PASSWORD,Current PIN,New PIN# PIN: Range: Letters and Numerals Length Limit: 1 ~ 10 Default: 0000 Note: Tracker will return “SET PASSWORD OK” when received this command. 10.7 Google Map Search GOOGLE,Current PIN# Note: Tracker will return below message when received this command. http://maps.google.
TSDT1-B BLE 5.0 Wireless Door and Temperature Sensor TSR1-B BLE 5.0 Wireless Relay TR021 Lock Rope (400mm) 12. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
IMPORTANT NOTICE: FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. 13. ISEDC Warning This device complies with Innovation, Science, and Economic Development Canada licenceexempt RSS standard(s).