This device support WLAN 2.4GHz and 5GHz 2T2R and use spatial multiplexing MIMO(SM-MIMO) technology. Drivers support Windows,Linux,Android 2.
Dimension tolerance range: Memo: WL_HOST_WAKE has pulled high at module internal RESET module internal connect to main chip_en, pull high, host don't need pull high. RESET's voltage range 3.3v±10%, 0-0.9v is lower. WL_HOST_WAKE's voltage range 2.97--3.3v, 0-0.33v is lower.
The instruction manual of WC0SR2511 Model WC0SR2511 Safety regulations 1. It is not allowed to change the transmission frequency and increase the transmission power (including additional RF power amplifier). It is not allowed to connect the antenna or use other transmitting antennas without authorization. 2. This cannot be used when there is harmful interference to all kinds of legitimate radio communication business.
Interface USB2.0 Frequency and channel 2.4GHz 1~ 11 5150-5250, 5.25~5.35GHz, 5.47~5.725GHz, 5725-5850MHz *Note: If the design and specifications are changed, no notice shall be given.
The host device should be labeled with Contains “FCC ID: ARS-WC0SR2511” or Contains “IC: 9190A-WC0SR2511” This device complies with Part 15 of the FCC / ISED’s licence-exempt RSSs Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
This is a module device, when it was installed to the host device, the host device should be labeled with“ Contains FCC ID:ARS-WC0SR2511”or “Contains IC: 9190A-WC0SR2511” This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
conforme aus CNR d’Innovation, Science et Développement économique Canada applicables aux apparerils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Compliance with KDB996369 D03 OEM Manual 1. List of applicable FCC rules WiFi 2412-2462MHz FCC Part 15.247 Max output power 16.71dBm WiFi 5180-5240MHz，5260-5320MHz，5500-5700MHz，5745-5825MHz FCC Part 15.407, Max output power 17.51dBm 2. Summarize the specific operational use conditions When use this modular transmitter, please do not change the antenna and antenna gain,the power setting and country code can not be changed. The Antenna type is Planar antenna and 2T2R 2400-2483.5MHz Peak Gain: ANTA: 2.
can use the software control the modular working at test mode, select the transmit mode, channel and power setting. 9.
