TABLE OF CONTENTS Before Use…………………...………………………………………….…… 2 Safety Precautions………………………………………………………..… 3 For Your Safety Reason………………………………………………….… 7 Important Safety Instruction……………………………………………… 8 Introduction ……………………………………………………..……….… 10 Part Names and Function ……………………………………………….... 11 Installation ……………………………………………………………….… 12-13 Basic Operations …………………………………………………………… 15 Table of Signals Supported ……………………………………………...… 16 Troubleshooting ……………………………………………………….
Before Use Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Precautions Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of the product. Read the following safety instructions before starting the operation.
WARNING Keep the product away from moisture: Do not expose this appliance to rain or moisture. If water penetrates into the product, stop the operation; unplug the connector and contact with the Service Center. Continuous use in this case may result in fire or electric shock. Do not place any objects on the top of the product: Spilled water or metal objects may cause short circuit, fire or electric shock if they penetrate into the housing of the product.
Do not install the product close to smoke or moisture: Fire or electric shock may be caused when the product is installed close to smoke or moisture. Do not installed the product in an area with heavy dust or high humidity: Fire or electric shock may be caused when the product is installed in a place with heavy dust or high humidity. Instructions for moving the product: Ensure that the power connector and any other leads are unplugged before moving the product.
Precautions 1. Read all safety instructions and the User Manual before using the product. 2. The safety instructions and User Manual should be maintained in good condition for future reference. 3. Unplug the power connector before cleaning the product. A wet cloth is sufficient for the cleaning of the product, never use liquid or spray cleaner for cleaning the product. 4. Always use the accessories recommended by the manufacturer to avoid any risk. 5.
For your safety reason The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. WARNING-When using electric products, basic precautions should always be followed, including the following: Read Instructions-All the safety and operating instructions should be read before the appliance is operated. Retain Instructions-The safety and operating instructions should be retained for future reference. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.
Object and Liquid Entry-Never push objects of any kind into this appliance through openings as they may touch dangerous voltage points do short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance. Damage Requiring Service-Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b.
Introduction Introduction to the PT4231 Plasma Monitor PT4231 is a seamless blend of cutting-edge visual technology and sophisticated design. At 42-inches, with a 16:9 aspect ratio, the PT4231 certainly makes a big impression. However, at a mere 4.3-inches/110 mm thin, the monitor’s sleek techno-art lines blend in well with your environment. PT4231crisp, vivid image quality will transform data from any graphic medium from PCs players-into art. And weighing only 79.
Part Names and Function 1. 2. 3. 4. 5. 6. POWER POWER/Standby Indicator INPUT Select MENU SETTING ADJ. + , ADJ. - Front View 1. POWER Turn the monitor’s power on and off. 2. POWER/Standby Indicator Window When the power is on …………………. Lights orange. When the power is standby ….……… Lights red. 3. INPUT Select Switch the input in the following order. DVI <=> D-sub 15 PIN 4. MENU Sets the On-Screen Display (OSD) Menu mode and displays the main menu. 5.
Installation Rear View MAIN POWER WITCH AC IN RS-232C DVI (29pin) D-sub RGB MAIN POWER SWITCH Turn on/off the AC power. AC IN Connect the included power cord here. RS232C Only use in factory. DVI (29pin) INPUT Input for a digital RGB signal (TMDS). D-sub(15Pin)INPUT Input for the analog RGB signal from personal computer, etc.
Installation Connections with Equipment that has a Digital Interface Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. * Use a DVI 29-pin signal cable when making connections to the DVI connector of the main unit. Note that the DVI terminal does not support analog RGB input source and HDCP protocol. Note: 1. Input TMDS signals conforming to DVI standards. The TMDS input corresponds to single link. 2.
Pin Assignments and signal for D-sub 15 pin RGB (Analog) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal (Analog) Red Green or sync-on-green Blue No Connection Ground Red ground Green ground Blue ground No Connection Sync signal ground No Connection Bi-directional DATA (SDA) Horizontal sync or Composite sync Vertical sync Data clock Pin Configuration and Signal of the DVI Connector Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Signal (Digital) T.M.D.S Data 2 T.
Basic Operations POWER 1. To power on and off the unit: Connect the power cord to your plasma monitor and wall AC power outlet. Push the main power switch on the bottom side of the plasma monitor (the main power switch can be access from the back side of the plasma monitor). The power indicator LED will flash and stabilized in red color. The monitor is in the STANDYBY mode when the LED light is stabilized in red color.
Table of Signals Supported Supported resolution y y When the screen mode is NORMAL, each signal is converted to a 640 dots × 480 lines signal. When the screen mode is FULL, each signal is converted to a 852 dots × 480 lines signal. Computer input signals supported by this system Dots × Lines 640×400 640×480 848×480 Vertical Horizontal Frequency Frequency Sync Polarity (Hz) (kHz) 70.1 31.
Troubleshooting If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service. Symptom Checks No picture is produced. y Is the monitor’s power cord plugged into a power outlet? y Are all the monitor’s indicators off? Poor picture with RGB signal input. y Improper control setting. Incorrect 15 PIN connector pin connections. y Are the tint and colors properly adjusted? Tint is poor or colors are weak.
Specifications Product Name Screen Size Aspect Ratio Resolution Pixel Pitch Color Reproduction Signals Synchronization range RS232 Control Power Supply Current Rating Power Consumption Dimensions Weight Environmental Considerations Operating Temperature Humidity Storage Temperature Humidity Front panel User Controls Other features Accessories Regulatory Compliance Plasma Monitor PT4231 36.3"(H) × 20.4"(V) inches 921(H) × 518(V) mm diagonal 42" 16 : 9 852(H) × 480(V) pixels 0.043"(H) × 0.044"(V) inches 1.